Home › BODY › INSTRUMENT PANEL › UPPER INSTRUMENT PANEL (for Hatchback)

UPPER INSTRUMENT PANEL (for Hatchback) > REMOVAL

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B118994E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.



3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



    E107742E01
  1. Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



    E107744E01
  1. Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



5. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.



    B132364
  1. Disengage the 2 claws and 5 clips.



    B132365E01
  1. After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.



6. REMOVE COMBINATION METER ASSEMBLY


E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



7. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



9. REMOVE FRONT PILLAR GARNISH RH


    B117693E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117694
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114312
  1. Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.



    B127674
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127670E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



  1. w/ Curtain Shield Airbag:



      B114313E01
    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



10. REMOVE FRONT PILLAR GARNISH LH


    B117695E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117696
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114316
  1. Using a clip remover, remove the 4 wire harness clamps.



    B127673
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127669E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



    B114317E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



11. REMOVE NO. 1 SWITCH HOLE BASE


B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.



12. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B105351
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



13. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 4 <B> screws.


    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.



  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.


    B105355E01



14. REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


B105356
  1. Remove the 2 <A> screws.

  1. Pull the instrument the panel box door toward the rear of the vehicle, disengage the 2 claws and 2 clips and remove the instrument panel box door.



15. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


B105358
  1. Remove the 2 <A> screws.

  1. Pull the instrument the panel box door toward the rear of the vehicle, disengage the 2 claws and 2 clips and remove the instrument panel box door.



16. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING


B105360
  1. Remove screw <A> and remove the cup holder spring.



17. REMOVE NO. 1 INSTRUMENT PANEL CUP HOLDER


B108174E01
  1. Slightly deform portion A of the cup holder by pressing it and release the stopper.



    B108173E01
  1. Using a screwdriver with its tip wrapped in protective tape, prize the hinge portion of the cup holder from side to side, while being careful not to apply excessive load to the axis of the instrument panel upper, and remove the cup holder.



18. REMOVE NO. 2 INSTRUMENT PANEL CUP HOLDER

HINT:
Use the same procedure as for the RH side.



19. REMOVE NO. 2 HEATER TO REGISTER DUCT


B108177
  1. Remove the 2 <A> screws and remove the register duct.



20. REMOVE NO. 1 HEATER TO REGISTER DUCT


B108176
  1. Remove the 2 <A> screws and remove the register duct.



21. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


B108178
  1. Disengage the 3 claws and remove the register.

    HINT:
    Use the same procedure as for the opposite side.



22. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY


B108295E01
  1. Remove the wire harness from the 2 claws of the instrument panel.

  1. Disengage the 10 hooks and remove the instrument panel passenger airbag.



23. REMOVE INSTRUMENT PANEL CUSHION


B108179
  1. Remove the instrument panel cushion from the instrument panel upper.



24. REMOVE NO. 1 INSTRUMENT PANEL CUSHION


B108203
  1. Remove the instrument panel cushion from the instrument panel upper.



25. REMOVE NO. 2 INSTRUMENT PANEL CUSHION


B108204
  1. Remove the instrument panel cushion from the instrument panel upper.



26. REMOVE NO. 3 INSTRUMENT PANEL CUSHION


B108205
  1. Remove the 2 instrument panel cushions from the instrument panel upper.