Home › BODY › INSTRUMENT PANEL › LOWER INSTRUMENT PANEL (for Hatchback)

LOWER INSTRUMENT PANEL (for Hatchback) > REMOVAL

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B118995E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



    E107742E01
  1. Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



    E107744E01
  1. Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



5. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.



    B132364
  1. Disengage the 2 claws and 5 clips.



    B132365E01
  1. After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.



6. REMOVE COMBINATION METER ASSEMBLY


E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (Except CD Player)


E116762
  1. w/ Cassette Tape Player:

    1. Connect the connectors.

    2. Install the radio receiver with the 4 screws.



    I101590
  1. w/ CD Player:

    1. Connect the connectors.

    2. Engage the 4 clips and 2 claws and install the radio receiver.

    3. Install the 4 screws.



8. REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver)


B108169
  1. Remove the 4 bolts and the radio tuner opening cover.



9. REMOVE RADIO RECEIVER ASSEMBLY


E116761
  1. w/ Cassette Tape Player:

    1. Remove the 4 screws.

    2. Disconnect the connectors and remove the radio receiver.



    E116821E02
  1. w/ CD Player:

    1. Remove the 4 screws.

    2. Disengage the 2 claws and 4 clips and the radio receiver.

      NOTICE:
      1. Grip the rib portion of the radio receiver by hand to remove it.
      2. To avoid breakage of the radio receiver when removing it, do not apply excessive force to the register or pull out the link or panel portions.

    3. Disconnect the connectors.



10. REMOVE AIR CONDITIONER PANEL SUB-ASSEMBLY


I101155
  1. Disengage the 3 clips and 2 claws and remove the air conditioning panel.



    I101156
  1. Disconnect the 3 connectors and clamp.



11. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I101157
  1. Disconnect the air mix control cable from the clamp.

  1. Disengage the 2 claws and disconnect the air mix damper control cable.



12. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I101158
  1. Disengage the 2 claws and disconnect the defroster damper control cable.



13. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I101159
  1. Disengage the 2 claws and disconnect the air inlet damper control cable.



14. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



15. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



16. REMOVE FRONT PILLAR GARNISH RH


    B117693E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117694
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114312
  1. Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.



    B127674
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127670E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



  1. w/ Curtain Shield Airbag:



      B114313E01
    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



17. REMOVE FRONT PILLAR GARNISH LH


    B117695E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117696
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114316
  1. Using a clip remover, remove the 4 wire harness clamps.



    B127673
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127669E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



    B114317E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



18. REMOVE NO. 1 SWITCH HOLE BASE


B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.



19. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B105351
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



20. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 4 <B> screws.


    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.



  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.


    B105355E01



21. REMOVE FRONT DOOR SCUFF PLATE RH


    B114287
  1. Disengage the 6 claws and remove the rear door scuff plate.



22. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



23. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH


    B114571
  1. Disengage the 4 claws and remove the instrument panel under cover.



24. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH


    B114572
  1. Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.



25. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



26. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



27. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


B208627
  1. Remove the shift lever knob.



28. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)


B208631
  1. Disengage the 6 claws and remove the shifting hole cover.



29. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


30. REMOVE CONSOLE BOX COVER REAR


B118991
  1. Disengage the 8 claws and remove the console box rear cover.



31. REMOVE CONSOLE BOX CARPET


B118992
  1. Remove the console box carpet.



32. REMOVE CONSOLE BOX ASSEMBLY REAR


B118993
  1. Remove bolt <F>.

  1. Disengage the 2 clips and remove the console box rear.



33. REMOVE INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag)


B108185
  1. Disengage the 4 claws and open the instrument panel under tray.



    B108187
  1. Remove the 2 <A> screws.

  1. Disengage the 4 claws and remove the instrument panel under tray.



34. REMOVE STEERING COLUMN COVER LOWER (w/ Driver Side Knee Airbag)


    C117204E01
  1. Remove the 3 screws, disengage the 2 claws, release the tilt lever and remove the steering column lower cover.



    C117205E01
  1. Disengage the claw and remove the steering column upper cover.



35. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


C119072E01
  1. Remove the 4 bolts.

  1. Disengage the 6 claws and remove the driver side knee airbag assembly.

  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.



36. REMOVE INSTRUMENT PANEL BOX


B108188E01
  1. Open the instrument panel box.

  1. Pull the hinge side of the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.

  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.



37. REMOVE NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


B108190
  1. Disengage the 4 claws and remove the heater to register duct.



38. DISCONNECT ANTENNA CORD SUB-ASSEMBLY


B108200
  1. for LHD:

    1. Disconnect the 2 antenna cord clamps.



    B108160E01
  1. for RHD:

    1. Disconnect the 3 antenna cord clamps.



39. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B108191
  1. Disengage the 3 claws and separate the hood lock control lever.



40. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


B108192
  1. Disengage the 2 claws and disconnect the DLC3 connector.

  1. Disconnect the clamps and connectors.



  1. Remove the 5 <D> bolts, 2 <E> bolts, screw <G> and screw <H> and remove the lower instrument panel.


    B108193E01



41. REMOVE POWER OUTLET SOCKET ASSEMBLY


    B117776
  1. Disconnect the power outlet connector.



    B117777
  1. Using a screwdriver, disengage the claw, then turn the power outlet socket counterclockwise and push the power outlet socket half way out.



    B117778
  1. Align the protrusion of the power outlet socket with the cutout of the power outlet socket cover and then push the power outlet socket out.



42. REMOVE POWER OUTLET SOCKET COVER


    B117779
  1. Disengage the 2 claws and remove the power outlet socket cover.



43. REMOVE CIGARETTE LIGHTER KNOB


    B119923
  1. Remove the cigarette lighter knob.



44. REMOVE CIGARETTE LIGHTER COVER


    B119925
  1. Disconnect the cigarette lighter connector.



    B119926
  1. Using a screwdriver, disengage the claw, then turn the cigarette lighter socket counterclockwise and push the cigarette lighter socket half way out.



    B119927
  1. Align the protrusion of the cigarette lighter socket with the cutout of the cigarette lighter indicator lens and then push out the cigarette lighter socket.



    B119924
  1. Disengage the 2 claws and remove the cigarette lighter cover.



45. REMOVE CIGARETTE LIGHTER INDICATOR LENS


B119928
  1. Disengage the 2 claws and remove the cigarette lighter indicator lens.



46. REMOVE OUTER MIRROR SWITCH ASSEMBLY


B108225
  1. Disengage the 2 claws and remove the outer mirror switch.



47. REMOVE HEADLIGHT LEVELING SWITCH


B108226
  1. Disengage the 2 claws and remove the headlight leveling switch.



48. REMOVE AIRBAG CUT OFF SWITCH CYLINDER


B108231
  1. Disengage the 2 claws and remove the airbag cut off switch cylinder.



49. REMOVE FRONT PANEL SEAL


B108221
  1. Remove the front panel seal.



50. REMOVE INSTRUMENT PANEL BOX SPRING


B108194
  1. Remove screw <A> and the instrument panel box spring.



51. REMOVE NO. 1 INSTRUMENT PANEL BOX


B108196
  1. Remove the 2 <A> screws and the instrument panel box.



52. REMOVE NO. 2 INSTRUMENT PANEL BOX


B108195
  1. Remove the 2 <A> screws and the instrument panel box.



53. REMOVE INSTRUMENT CLUSTER FINISH PANEL SEAL


B108197
  1. Disengage the 5 claws and remove the panel seal.