Home › BODY › INSTRUMENT PANEL › LOWER INSTRUMENT PANEL (for Sedan)

LOWER INSTRUMENT PANEL (for Sedan) > REMOVAL

for Preparation Click here


HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B132394E01



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


3. REMOVE INSTRUMENT PANEL CUP HOLDER RH


B132398E01
  1. Open the instrument panel cup holder.

  1. Flex both sides of the instrument panel cup holder and disengage the 2 stoppers.



    B132399
  1. Disengage the spring.



    B132400E01
  1. Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time.



4. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING RH


B132402
  1. Remove the spring.



5. REMOVE INSTRUMENT PANEL CUP HOLDER LH


B132403E01
  1. Open the instrument panel cup holder.

  1. Flex both sides of the instrument panel cup holder and disengage the 2 stoppers.



    B132404E01
  1. Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time.



6. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING LH


B132406
  1. Remove the spring.



7. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.



8. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.



9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end RH.



10. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


E116832
  1. Disengage the 4 claws and 5 clips and remove the instrument cluster finish panel.



11. REMOVE COMBINATION METER ASSEMBLY


E116819
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



12. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY


B132395
  1. Disengage the 2 claws and 4 clips and remove the instrument cluster panel center.



13. REMOVE STEREO OPENING COVER (w/o Radio Receiver)


B132396
  1. Remove the 4 screws and remove the stereo opening cover.



14. REMOVE RADIO RECEIVER ASSEMBLY


    B138302
  1. Remove the 4 bolts and the radio receiver.



    B138304
  1. Disconnect the plug.

  1. Disconnect the 2 radio connectors.



15. REMOVE AIR CONDITIONING PANEL ASSEMBLY


I102566
  1. Disengage the 4 clips and 2 claws and remove the air conditioning panel.



    I102567
  1. Disconnect the 3 connectors and 4 clamps.



16. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I102568
  1. Disconnect the air mix control cable from the clamp.

  1. Disengage the 2 claws and disconnect the air mix damper control cable.



17. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I102569
  1. Disengage the 2 claws and disconnect the defroster damper control cable.



18. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I102570
  1. Disengage the 2 claws and disconnect the air inlet damper control cable.



19. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



20. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



21. REMOVE FRONT PILLAR GARNISH RH


    B134777E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134779
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134787
  1. Disconnect the antenna connector.

  1. Using a clip remover, remove the 3 clamps.



    B138437E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



22. REMOVE FRONT PILLAR GARNISH LH


    B134778E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134780
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134789
  1. Using a clip remover, remove the 4 clamps.



    B138438E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



23. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B132319E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.



    B132320E01
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



24. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B130309E01
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).

  1. Engage the 5 claws at the front side of the instrument panel.



  1. Engage the 7 clips at the rear side of the instrument panel.


    B132324



  1. Install the upper instrument panel with the 2 <C> bolts and the 2 <B> screws.


    B132323E01

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf } for bolt <C>



    B132386
  1. Connect the passenger airbag connector and clamp.



25. REMOVE FRONT DOOR SCUFF PLATE RH


    B134764
  1. Disengage the 11 claws and remove the front door scuff plate.



26. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



27. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



28. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



29. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132387
  1. Remove the shift lever knob.



30. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B132347
  1. Shift the shift lever into the N position.

  1. Disengage the 5 clips and the claw and remove the upper console panel.



31. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B132348
  1. Disengage the 3 clips and 3 claws.

  1. Disconnect the connector and remove the console upper rear panel.



32. REMOVE CONSOLE BOX CARPET


B132346
  1. Remove the console box carpet.



33. REMOVE REAR CONSOLE BOX ASSEMBLY


    B132349
  1. Disconnect the clamp.

  1. Remove the 2 bolts and 2 screws.

  1. Disengage the 4 claws and remove the rear console box.



34. REMOVE INSTRUMENT PAD LOWER LH


B132339
  1. Remove screw <I>.

  1. Disengage the claw and 3 clips and remove the instrument panel pad lower.



35. REMOVE INSTRUMENT PAD LOWER RH


B132340
  1. Remove screw <I>.

  1. Disengage the claw and 3 clips and remove the instrument panel pad lower.



36. REMOVE INSTRUMENT PANEL UNDER TRAY


B132341
  1. Disengage the 4 claws and open the instrument panel under tray.



    B132333
  1. Remove the 2 <A> screws.

  1. Disengage the 6 claws and remove the instrument panel under tray.



37. REMOVE INSTRUMENT PANEL BOX


B132334E01
  1. Open the instrument panel box.

  1. Pull the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.



    B132335E01
  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.



38. DISCONNECT ANTENNA CORD SUB-ASSEMBLY


    B132369
  1. for LHD:

    1. Disconnect the 5 antenna cord clamps.



    B132370
  1. for RHD:

    1. Disconnect the 4 antenna cord clamps.



39. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B132338
  1. Disengage the 3 claws and separate the hood lock control lever.



40. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


B108192
  1. Disengage the 2 claws and disconnect the DLC3 connector.

  1. Disconnect the clamps and connectors.



  1. Remove the 6 <D> bolts, 2 <E> bolts, screw <G> and screw <H> and remove the lower instrument panel.


    B132342E01



41. REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY LH


B132343
  1. Remove the 3 <A> screws and the instrument panel cup holder.



42. REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY RH


B132344
  1. Remove the 3 <A> screws and the instrument panel box.



43. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


B132392
  1. Disengage the claw and remove the glove compartment door stopper.



44. REMOVE OUTER MIRROR SWITCH ASSEMBLY


B132357
  1. Disengage the 2 claws and remove the outer mirror switch.



45. REMOVE HEADLIGHT LEVELING SWITCH


B132359
  1. Disengage the 2 claws and remove the headlight leveling switch.



46. REMOVE STEREO JACK ADAPTER ASSEMBLY


B132360
  1. Disengage the 2 claws and remove the stereo jack adapter.



47. REMOVE INSTRUMENT PANEL HOLE COVER


B130144
  1. Remove the 2 <H> screws and the instrument hole cover.



48. REMOVE INSTRUMENT CLUSTER FINISH PANEL SEAL


B132393
  1. Disengage the 5 claws and remove the panel seal.



49. REMOVE INSTRUMENT PANEL NO. 1 SAFETY PAD


B132362
  1. Remove the safety pad.



50. REMOVE INSTRUMENT PANEL NO. 2 SAFETY PAD


B132361
  1. Remove the safety pad.