Home › ENGINE ยท 2NZ-FE › CHARGING › GENERATOR

GENERATOR > REASSEMBLY

for Preparation Click here



1. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the drive end frame on the generator rotor assembly.

    NOTICE:
    Do not drop the generator rotor assembly.

  1. Install the generator rotor assembly and plate retainer.



    A033357E01
  1. Using a 30 mm socket wrench and press, slowly press in the rectifier end frame.



    A117361
  1. Install the 4 nuts and clip cord.

    Torque:
    4.5 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. Install the 3 terminal insulators onto the rectifier end frame.



2. INSTALL GENERATOR HOLDER WITH RECTIFIER


A117360
  1. Install the generator rectifier holder with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }



3. INSTALL GENERATOR REGULATOR ASSEMBLY


A117295
  1. Install the generator regulator assembly with the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }



4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY


A117359
  1. Install the plate seal.

  1. Install the generator brush holder assembly with the 3 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 17 in.*lbf }

  1. Install the brush cover onto the generator brush holder assembly.

  1. Install the rear end cover with the 2 nuts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }

  1. Install the rectifier plate with the nut and screw.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf } for nut
    3.8 N*m{ 39 kgf*cm , 34 in.*lbf } for bolt

  1. Install the terminal insulator with the nut.

    Torque:
    4.1 N*m{ 42 kgf*cm , 36 in.*lbf }



5. INSTALL GENERATOR PULLEY


A193553E01
SST
09820-63011   (09820-06010, 09820-06021)
HINT 
SST 1-A and B
09820 - 06010
SST 2
09820 - 06021
  1. Clamp the generator housing stay in a vise.

  1. Install the generator pulley onto the generator rotor shaft by tightening the generator pulley nut by hand.

  1. Hold SST 1-A with a torque wrench, and tighten SST 1-B clockwise to the specified torque.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

    NOTICE:
    Check that SST is securely fitted onto the generator rotor shaft.



    A193554E01
  1. Insert SST 2, and attach the pulley nut to SST 2.



    A193557E01
  1. Tighten the generator pulley nut by turning SST 1-A in the direction shown in the illustration.

    Torque:
    133 N*m{ 1356 kgf*cm , 98 ft.*lbf }

    HINT:
    Hold the adjustable wrench against the vise and tighten the nut securely.

  1. Remove SST 2 from the generator.



    A193556E01
  1. Turn SST 1-B, and remove SST 1-A and B.

  1. Turn the generator pulley, and check that the generator pulley moves smoothly.