Home › BODY › EXTERIOR › NAME PLATE (for Hatchback)

NAME PLATE (for Hatchback) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


    B114602E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 2 luggage compartment door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    158.8 mm (6.252 in.)
    b
    40.3 mm (1.587 in.)
    c
    255.9 mm (10.075 in.)
    d
    157.6 mm (6.205 in.)

    NOTICE:
    Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



2. INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE


    B114603E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 1 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 1 luggage compartment door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    158.5 mm (6.24 in.)
    b
    41.7 mm (1.642 in.)
    c
    266.1 mm (10.476 in.)
    d
    156.4 mm (6.157 in.)

    NOTICE:
    Install the No. 1 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 1 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 1 luggage compartment door name plate.



3. INSTALL SYMBOL EMBLEM


    B117713
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.

      HINT:
      Heat at 40 to 60 °C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol emblem while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Insert the 2 bosses into the back door panel and install the symbol emblem.

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.



4. INSTALL RADIATOR GRILLE EMBLEM


    B114599
  1. Engage the 4 claws and install the radiator grille emblem.



5. INSTALL FRONT BUMPER COVER


    B114362
  1. Install the 2 clips and the screw grommet.



    B185295
  1. Engage the 6 claws and install the front bumper cover.

  1. Connect the 2 connectors.

    HINT:
    If the vehicle is equipped with fog lights, connect the connector.



    B209559
  1. Install the 7 clips.

  1. Install the 2 screw grommets.

  1. Tighten the 8 screws.



    B185052E01
  1. Remove the protective tape.