Home › BODY › EXTERIOR › NAME PLATE (for Sedan)

NAME PLATE (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL SYMBOL EMBLEM


    B134870E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol while any double-sided adhesive tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Align the 2 pins and install a new symbol emblem.

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.



2. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


    B134867E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 luggage compartment door name plate while any double-sided adhesive tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 2 luggage compartment door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    39.4 mm (1.551 in.)
    b
    44.7 mm (1.760 in.)
    c
    162.4 mm (6.394 in.)
    d
    17.8 mm (0.701 in.)

    NOTICE:
    Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 2 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



3. INSTALL NO. 6 LUGGAGE COMPARTMENT DOOR NAME PLATE


    B134864E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 6 luggage compartment door name plate while any double-sided adhesive tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided adhesive tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 6 luggage compartment door name plate as shown in the illustration.

    Installation position:
    Mark
    Measurement (along surface)
    a
    52.8 mm (2.079 in.)
    b
    17.1 mm (0.673 in.)
    c
    162.3 mm (0.390 in.)
    d
    20 mm (0.787 in.)

    NOTICE:
    Install the No. 6 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 6 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 6 luggage compartment door name plate.



4. INSTALL RADIATOR GRILLE EMBLEM


    B134824
  1. Engage the 4 claws and install the radiator grille emblem.



5. INSTALL FRONT BUMPER COVER


    B134801
  1. w/ Fog Light:

    1. Connect the 2 fog light connectors.

    2. Engage the 6 claws and install the front bumper cover.



    B134800
  1. w/o Fog Light:

    1. Engage the 6 claws and install the front bumper cover.



    B134805
  1. Install the 6 clips.

  1. Install the 2 screw grommets.

  1. Tighten the 7 screws and 3 bolts.



    B134799E01
  1. Remove the protective tape.