Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM (for Sedan)

METER / GAUGE SYSTEM (for Sedan) > TERMINALS OF ECU

for Preparation Click here



COMBINATION METER ASSEMBLY

E126885E03

  1. Disconnect the D1 combination meter assembly connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D1-1 (IG2) - Body ground
    B - Body ground
    Ignition switch signal
    Ignition switch off → ON
    Below 1 V → 11 to 14 V
    D1-2 (ECU-B) - Body ground
    L - Body ground
    Battery
    Always
    11 to 14 V
    D1-24 (ET) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Disconnect the D84 combination meter assembly connector.



  4. Measure the voltage of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D1-3 (FUEL) - Body ground
    V - Body ground
    Fuel level signal
    Ignition switch ON
    11 to 14V
    D1-10 (P/SB) - Body ground
    BE - Body ground
    Seat belt condition signal (Passenger side)
    Ignition switch ON
    P-BELT indicator light OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    D1-14 (ILL+) - Body ground
    G - Body ground
    Taillight signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    D1-16 (+S) - Body ground
    SB - Body ground
    Speed signal (Output)
    Driving at approximately
    20 km/h (12 mph)
    Pulse generation
    (See waveform 1)
    D1-17 (SI) - Body ground
    P - Body ground
    Speed signal (Input)
    Driving at approximately
    20 km/h (12 mph)
    Pulse generation
    (See waveform 1)
    D1-20 (CANH) - Body ground
    G - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    D1-21 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    D84-1 (CHG-) - Body ground
    L - Body ground
    Charge warning light signal
    Engine start
    Charge warning light ON → OFF
    Below 1 V → 11 to 14 V
    D84-2 (SW) - Body ground
    V - Body ground
    Brake fluid level warning light signal
    Ignition switch ON
    Brake fluid level warning light ON → OFF
    Below 1 V → 11 to 14 V
    D84-4 (EFI) - Body ground
    B - Body ground
    Check engine warning light signal
    Check engine warning light signal ON → OFF
    Below 1 V → 11 to 14 V
    D84-7 (FOG)*1 - Body ground
    R - Body ground
    Front fog signal
    Ignition switch ON
    Front fog switch OFF → ON
    Below 1 V → 11 to 14 V
    D84-8 (TURN L) - Body ground
    LG - Body ground
    Turn signal LH signal
    Ignition switch ON
    Turn signal LH indicator light ON
    Below 1 V → 11 to 14 V → Below 1 V
    D84-9 (PBLT) - Body ground
    BE - Body ground
    Seat belt warning light signal (Passenger side)
    Ignition switch ON
    Front passenger seat belt warning light OFF → ON → OFF
    Below 1 V → 11 to 14 V
    → Below 1 V
    D84-11 (BEAM-) - Body ground
    P - Body ground
    HI-BEAM indicator signal (-)
    BEAM indicator light ON → OFF
    Below 1 V → 11 to 14 V
    D84-12 (S) - Body ground
    Y - Body ground
    Engine oil pressure signal
    Engine oil pressure warning light ON → OFF
    Below 1 V → 11 to 14 V
    D84-14 (BEAM+) - Body ground
    GR - Body ground
    HI-BEAM indicator signal (+)
    Always
    11 to 14 V
    D84-15 (TURN R) - Body ground
    BR - Body ground
    Turn signal RH signal
    Ignition switch ON
    Turn signal RH indicator light OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    D84-16 (IND) - Body ground
    G - Body ground
    Taillight indicator signal
    Headlight dimmer switch
    (TAIL) OFF → ON
    Below 1 V → 11 to 14 V
    D84-17 (ODO) - Body ground
    L - Body ground
    Hazard switch signal
    Ignition switch ON
    5 V
    D84-18 (CLK) - Body ground
    R - Body ground
    Hazard switch signal
    Ignition switch ON (ACC)
    5 V
    D84-19 (E1) - Body ground
    GR - Body ground
    Hazard switch signal
    Ignition switch ON
    Below 1 V

    1. *1: w/ Front Fog Light
    If the result is not as specified, the combination meter assembly may have a malfunction.



      E115032E01
    1. Waveform 1: Using an oscilloscope
      Terminal Connections
      D1-16 (+S) - Body ground
      D1-17 (SI) - Body ground
      Tester Range
      5 V/DIV, 20 ms/DIV
      Vehicle Condition
      Driving at approximately 20 km/h (12 mph)

      HINT:
      As the vehicle speed increases, the cycle of the signal waveform narrows.

  5. Reconnect the combination meter assembly connectors.


MAIN BODY ECU

E114510E59


Text in Illustration 
*1
Rear view of Main Body ECU
-
-

B108641E52


Text in Illustration 
*1
Front view of Main Body ECU
-
-
  1. Disconnect the 4A, 4D and 4E main body ECU connectors.

  2. Measure the resistance of the wire harness side connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    4A-5 (RRCY) - Body ground
    G - Body ground
    Rear door courtesy switch signal (LH and RH)
    Rear door (LH and RH) CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4A-7 (BCTY) - Body ground
    SB - Body ground
    Luggage door courtesy switch signal
    Back door CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4A-21 (DCTY) - Body ground
    R - Body ground
    Front door courtesy switch signal (Driver Side)
    Front door (Driver Side) CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4A-24 (PCTY) - Body ground
    L - Body ground
    Front door courtesy switch signal (Passenger Side)
    Front door (Passenger Side) CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4D-7 (KSW) - Body ground
    Y - Body ground
    Key unlock warning switch signal
    Key inserted → removed
    10 kΩ or higher → Below 1 Ω
    4E-17 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU connectors.

  4. Measure the voltage of the wire harness side connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    4C-2 (PKB) - Body ground
    Y - Body ground
    Parking brake signal
    Parking brake warning light ON → OFF
    Below 1 V → 11 to 14 V
    D33-9 (DBKL) - Body ground
    W - Body ground
    Seat belt condition signal (Driver side)
    Driver seat belt warning light OFF → ON
    11 to 14 V → Below 1 V
    D33-22 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    D33-23 (CANH) - Body ground
    R - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, there may be a malfunction in the wire harness.


COMBINATION METER INTERNAL CIRCUIT

E191166E01


E197365E01


E197982E01


Connectors 
Terminal No.
Wire Harness Side
D1
1
Ignition switch
2
Battery
3
Fuel sender gauge assembly
10
Front seat inner belt assembly (Passenger side)
14
Headlight dimmer switch
16
Other ECU
17
Brake actuator*2
Speedometer sensor*3
20
CAN communication line
21
CAN communication line
24
Body ground
D84
1
Generator
2
Brake fluid level warning switch
4
ECM
7*1
Fog light relay
8
Turn signal flasher assembly
9
Hazard warning signal switch assembly
11
Headlight dimmer switch
12
Engine oil pressure switch
14
Battery
15
Turn signal flasher assembly
16
Headlight dimmer switch
17
Hazard warning signal switch assembly
18
Hazard warning signal switch assembly
19
Hazard warning signal switch assembly
  1. *1: w/ Front Fog Light
  2. *2: w/ ABS
  3. *3: w/o ABS