Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION



C080723



2. ADJUST TAPERED ROLLER BEARING PRELOAD
  1. Coat the front differential case and bearing with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.

    NOTICE:
    Do not install the drive pinion.



    C080710
  1. Install the transaxle housing onto the transaxle case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



    D025185E01
  1. Using SST and a small torque wrench, measure the preload of the differential gear.

    SST
    09564-32011  

    Preload:
    Bearing
    Standard
    New
    0.78 to 1.37 N*m (8.0 to 14.0 kgf*cm, 6.9 to 12.2 in.*lbf)
    Used
    0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)

    If the preload is not within the specifications, remove the differential from the transaxle case.
    Select a new transaxle case side adjusting shim in accordance with the following table.

    Adjusting shim thickness:
    mm (in.):
    Mark
    Thickness
    mm (in.)
    Mark
    Thickness
    mm (in.)
    A
    1.80 (0.0709)
    N
    2.26 (0.0890)
    B
    1.85 (0.0728)
    P
    2.29 (0.0902)
    C
    1.90 (0.0748)
    Q
    2.32 (0.0913)
    D
    1.95 (0.768)
    R
    2.35 (0.0925)
    E
    2.00 (0.0787)
    S
    2.40 (0.0945)
    F
    2.05 (0.0807)
    T
    2.45 (0.0965)
    G
    2.08 (0.0819)
    U
    2.50 (0.0984)
    H
    2.11 (0.0831)
    V
    2.55 (0.1004)
    J
    2.14 (0.0843)
    W
    2.60 (0.1024)
    K
    2.17 (0.0854)
    X
    2.65 (0.1043)
    L
    2.20 (0.0866)
    Y
    2.70 (0.1063)
    M
    2.23 (0.0878)




3. INSTALL BREATHER PLUG NO. 1


C123279
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it onto breather plug No. 1.

  1. Install breather plug No. 1 onto the transaxle case.



4. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE


C059795
  1. Install the differential gear lube apply tube onto the transaxle housing.

    NOTICE:
    Do not apply excessive force to the apply tube.



5. INSTALL TRANSMISSION LUBE APPLY TUBE


C059794
  1. Install the transmission lube apply tube onto the transaxle housing.

    NOTICE:
    Do not apply excessive force to the apply tube.



6. INSTALL TRANSAXLE APPLY TUBE CLAMP NO. 1


C059824
  1. Install transaxle apply tube clamp No. 1 onto the transaxle housing with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



7. INSTALL TRANSAXLE HOUSING OIL SEPARATOR


C059793
  1. Install the transaxle housing oil separator onto the transaxle housing with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. INSTALL TRANSMISSION CASE PLATE NO. 1


C059802
  1. Install transmission case plate No. 1 onto the transaxle case with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



9. INSTALL TRANSAXLE CASE NO. 1 PLUG


C059902
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the 2 transaxle case No. 1 plugs.

  1. Install the 2 transaxle case No. 1 plugs onto the transaxle housing.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



10. INSTALL TRANSAXLE HOUSING NO. 2 PLUG


C059823
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it onto the transaxle housing No. 2 plug.

  1. Install the transaxle housing No. 2 plug to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



11. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


D025186E01
  1. Coat a new oil seal with Toyota Genuine ATF Type T-IV.

  1. Using SST and a hammer, install the manual valve lever shaft oil seal onto the transaxle case.

    SST
    09950-60010   (09951-00210)
    09950-70010   (09951-07100)

    Oil seal drive in depth:
    0.75 to 1.25 mm (0.030 to 0.049 in.)



12. INSTALL PARKING LOCK PAWL


C059865
  1. Coat the parking lock pawl shaft with Toyota Genuine ATF Type T-IV.

  1. Install the parking lock pawl shaft, torsion spring and parking lock pawl onto the transaxle case.

    NOTICE:
    Check that the edge of the torsion spring fits into the groove securely.



13. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY


C059863
  1. Install the manual detent spring with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



14. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


C060849
  1. Install the parking lock rod onto the manual valve lever.



15. INSTALL MANUAL VALVE LEVER SHAFT


C059855E01
  1. Coat the manual valve lever with Toyota Genuine ATF Type T-IV.

  1. Install a new spacer onto the manual valve lever.

  1. Install the manual valve lever shaft and manual valve lever.

    NOTICE:
    Do not damage the oil seal when installing the manual valve lever shaft.

  1. Using a pin punch and hammer, drive in the spring pin.

  1. Turn the spacer and lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.
    Using a pin punch, stake the spacer through the small hole.
    Check that the spacer does not turn.



16. INSTALL PARKING LOCK PAWL BRACKET


C059860
  1. Install the parking lock pawl bracket with the 2 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



17. INSTALL 1ST AND REVERSE BRAKE O-RING


C080716
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the 1st and reverse brake piston.



18. INSTALL 1ST AND REVERSE BRAKE PISTON


C059900
  1. Coat the 1st and reverse brake piston with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.

    NOTICE:
    Do not damage the O-ring of the 1st and reverse brake piston.



19. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C059856
  1. Coat the 1st and reverse brake return spring with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



20. INSTALL 1ST AND REVERSE BRAKE DISC


C082195E01
  1. Coat the 4 plates, 4 discs and flange with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.

    NOTICE:
    Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



    C060825E01
  1. Using SST, a press and a screwdriver, install the snap ring.

    SST
    09387-00100  
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the snap ring is installed in the groove of the transaxle case correctly.



21. INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE


D025187E01
  1. Using a dial indicator and measuring terminal (SST), measure the 1st and reverse brake piston stroke while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).

    SST
    09350-36010   (09350-06110)

    Piston stroke:
    0.791 to 1.489 mm (0.031 to 0.057 in.)

    If the piston stroke is outside the specifications, inspect the discs, plates and flange.



22. INSTALL COUNTER DRIVE GEAR


C080718E01
  1. Using SST and a press, install the counter drive gear.

    SST
    09223-15030  
    09387-00060  
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

    NOTICE:
    Do not apply excessive force to the transaxle case.



23. INSTALL PLANETARY RING GEAR


C059866
  1. Install the planetary ring gear onto the new planetary ring gear flange and fix the snap ring using a screwdriver.



24. INSTALL PLANETARY RING GEAR FLANGE


C080719E01
  1. Using SST and a press, install the planetary ring gear.

    SST
    09223-15030  
    09387-00060  
    09950-60010   (09951-00500)
    09950-70010   (09951-07100)



25. INSTALL COUNTER DRIVE GEAR NUT
  1. Using a 55 mm socket wrench, install a new counter drive gear nut onto the planetary gear flange.

    HINT:
    Torque : 100 N*m (1,020 kgf*cm, 74 ft.*lbf)



    C060714
  1. Inspect the preload of the counter drive gear bearing.

    Preload:
    0.05 to 0.35 N*m (0.5 to 3.6 kgf*cm, 0.43 to 3.12 in.*lbf)

    HINT:
    Tighten the counter drive gear nut gradually so that the preload is within the specifications.



    C080715E01
  1. Using SST, lift the transaxle case.

    SST
    09213-14010  
    09387-00060  



    C060715
  1. Using a chisel and a hammer, stake the counter drive gear nut.



26. INSTALL PLANETARY GEAR ASSEMBLY


C059857
  1. Coat the planetary gear with Toyota Genuine ATF Type T-IV, and install it onto the transaxle housing.



27. INSTALL 1 WAY CLUTCH NO. 2


C059854
  1. Coat 1-way clutch No. 2 with Toyota Genuine ATF Type T-IV, and install it onto the transaxle.



28. INSPECT 1 WAY CLUTCH NO. 2


D025182E01
  1. Check that the planetary gear turns freely counterclockwise and locks when turned clockwise.



29. INSTALL OUTER RACE RETAINER


C059853
  1. Install the anti-rattle clip in the place shown in the illustration (the space between the No. 2 1-way clutch outer race and transaxle case). Push the anti-rattle clip in until it makes a click sound.



30. INSTALL BRAKE DRUM GASKET


C059852
  1. Coat a new brake drum gasket with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



31. INSTALL 2ND BRAKE BRAKE DISC


D025188E01
  1. Coat the flange, 2 discs and 2 plates with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.

    NOTICE:
    Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



32. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C059850
  1. Coat the 2nd brake piston return spring with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



33. INSTALL 2ND BRAKE PISTON ASSEMBLY


C060853
  1. Coat the 2nd brake piston with Toyota Genuine ATF Type T-IV, and install it as shown in the illustration.



    C059837E01
  1. Using SST, a press and a screwdriver, remove the snap ring.

    SST
    09387-00100  
    09950-70010   (09951-07100)



34. INSTALL FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE


C060847
  1. Coat the thrust bearing race with Toyota Genuine ATF Type T-IV, and install it onto the front planetary sun gear.



35. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY


C060845
  1. Coat the planetary sun gear with Toyota Genuine ATF Type T-IV, and install it onto the transaxle.



36. INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


C059895
  1. Using a screwdriver, install the snap ring onto the transaxle case.



37. INSTALL PLANETARY CARRIER THRUST WASHER


C059890
  1. Coat the planetary carrier thrust washer with petroleum jelly, and install it onto the planetary gear.



38. INSTALL 1 WAY CLUTCH ASSEMBLY


C059835
  1. Coat planetary carrier thrust washer No. 2 with petroleum jelly.

  1. Install planetary carrier thrust washer No. 2 and the 1-way clutch onto the planetary sun gear.



39. INSPECT 1 WAY CLUTCH ASSEMBLY


D025181E02
  1. Hold the rear planetary sun gear and turn the 1 way clutch.

  1. Make sure that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



40. INSTALL PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING


C059836
  1. Coat the needle roller bearing with Toyota Genuine ATF Type T-IV, and install it onto the rear planetary gear.



41. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY


C059834
  1. Coat the rear planetary sun gear with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



42. INSTALL FORWARD CLUTCH HUB THRUST BEARING RACE


C059889
  1. Coat the thrust bearing race with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



43. INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


C059833
  1. Coat the thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it onto the forward clutch hub.



44. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY


C059831
  1. Coat the forward clutch hub with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



45. INSTALL SUN GEAR REAR THRUST BEARING


C059832
  1. Coat the thrust bearing and 2 bearing races with Toyota Genuine ATF Type T-IV, and install them onto the intermediate shaft.



46. INSTALL INTERMEDIATE SHAFT ASSEMBLY


C059830
  1. Coat the intermediate shaft with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



47. INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC


D025189E01
  1. Coat the plate, 2 discs and 2 flanges with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.

    NOTICE:
    Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



48. INSPECT 2ND COAST AND OVER DRIVE BRAKE FLANGE, DISC AND PLATE


C059893E01
  1. Using a straight edge and vernier calipers, measure dimension A from the transaxle case end surface to the brake flange.



    C059894E01
  1. Using a straight edge and vernier calipers, measure dimension B from the piston to the edge surface of the transaxle rear cover assembly.

  1. Calcurate the clearance from the measured dimensions A and B.

    Piston clearance:
    0.65 to 1.05 mm (0.0256 to 0.0413 in.)

    HINT:
    1. Piston clearance = Dimension A - Dimension B.
    2. If the result is not as specified, select a new brake flange.

    Flange thickness:
    Mark
    Thickness
    mm (in.)
    Piston stroke value
    mm (in.)
    0
    3.0
    (0.118)
    0.738 to 0.949
    (0.02905 to 0.03736)
    1
    3.2
    (0.126)
    0.950 to 1.149
    (0.03740 to 0.04524)
    2
    3.4
    (0.134)
    1.150 to 1.349
    (0.04528 to 0.05311)
    3
    3.6
    (0.142)
    1.350 to 1.549
    (0.05315 to 0.06098)
    0
    3.8
    (0.150)
    1.550 to 1.702
    (0.06102 to 0.06701)



49. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET


C059827
  1. Coat 4 new apply gaskets with Toyota Genuine ATF Type T-IV, and install them onto the transaxle rear cover.



50. INSTALL FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


C059826
  1. Coat the thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it onto the forward and reverse clutch.



51. INSTALL TRANSAXLE REAR COVER ASSEMBLY


C059899
  1. Apply FIPG to the transaxle rear cover.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent



    C059804
  1. Install the transaxle rear cover onto the transaxle case with the 9 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



52. INSTALL GOVERNOR APPLY GASKET NO. 2


C059803
  1. Coat a new governor apply gasket No. 2 with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



53. INSTALL DIFFERENTIAL GEAR ASSEMBLY


C059801
  1. Coat the differential gear and drive pinion with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.



54. INSTALL DIRECT CLUTCH HUB


C059825
  1. Coat the direct clutch hub with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



55. INSTALL PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING


C060793
  1. Coat the thrust bearing race and thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.



56. INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING


C059849
  1. Coat the thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.

    NOTICE:
    Check the direction of the bearing.



57. INSTALL INPUT SHAFT ASSEMBLY


C059800
  1. Coat the input shaft with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



58. INSTALL OIL PUMP ASSEMBLY


C080728
  1. Place the oil pump through the input shaft, and align the bolt holes in the oil pump with those in the transaxle case.

  1. Install the 6 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



59. INSPECT INPUT SHAFT ASSEMBLY


C080729
  1. Make sure that the input shaft turns smoothly.



60. INSPECT INPUT SHAFT END PLAY


C080727
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.3 to 0.9 mm (0.012 to 0.035 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.



61. INSTALL TRANSAXLE HOUSING


C059886
  1. Apply FIPG to the transaxle housing.

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent



    C080710E01
  1. Install the transaxle housing onto the transaxle case with the 16 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    HINT:
    Apply seal packing or the equivalent to the 4 bolts indicated by arrows.

    Seal packing:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent



62. INSTALL B-1 ACCUMULATOR PISTON COMPRESSION SPRING


C060004
  1. Install the B-1 accumulator piston compression spring onto the piston B-1 accumulator.



63. INSTALL PISTON B-1 ACCUMULATOR


D025193
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the B-1 accumulator piston.



    C060822
  1. Coat the B-1 accumulator piston with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



64. INSTALL C-1 ACCUMULATOR SPRING SUB-ASSEMBLY


C059790
  1. Install the C-1 accumulator spring into the C-1 accumulator piston.



65. INSTALL C-1 ACCUMULATOR PISTON


D025194
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV and install them onto the C-1 accumulator piston.



    C060823
  1. Coat the C-1 accumulator piston with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



66. INSTALL C-2 ACCUMULATOR SPRING SUB-ASSEMBLY


C059787
  1. Install the C-2 accumulator spring onto the C-2 accumulator piston with the snap ring.



67. INSTALL C-2 ACCUMULATOR PISTON


D025195
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the C-2 accumulator piston.



    C060824
  1. Coat the C-2 accumulator piston with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



68. INSTALL CHECK BALL BODY


C059785
  1. Coat the spring and the check ball body with Toyota Genuine ATF Type T-IV, and install them onto the transaxle case.



69. INSTALL GOVERNOR APPLY GASKET NO. 1


C059784
  1. Coat new governor apply gasket No. 1 with Toyota Genuine ATF Type T-IV, and install it onto the transaxle case.



70. INSTALL TRANSMISSION WIRE


D025196
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it onto the transmission wire.

  1. Insert the transmission wire into the transaxle.



    C057520
  1. Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



71. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


C057516E02
  1. Connect the connecting rod to the manual valve lever, and install the transmission valve body.



    D025197E01
  1. Install the 14 bolts into the positions shown in the illustration and tighten them uniformly.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    When installing the valve body onto the transaxle case, do not hold the solenoids.

    Bolt length:
    Bolt A:
    20 mm (0.79 in.)
    Bolt B:
    28 mm (1.10 in.)
    Bolt C:
    49 mm (1.93 in.)
    Bolt D:
    36 mm (1.42 in.)
    Bolt E :
    40 mm (1.57 in.)



    D025198E01
  1. Install the oil temperature sensor and connect the solenoid connectors.



72. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


C057509
  1. Install a new gasket onto the oil strainer.



    C057507
  1. Install the oil strainer onto the transaxle assembly with 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



73. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


C057519E01
  1. Install the 2 oil cleaner magnets onto the 2 positions shown in the illustration.



    C057506
  1. Install a new oil pan gasket and oil pan onto the transaxle assembly with 18 bolts.

    Torque:
    7.0 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Install a new drain plug gasket and drain plug to the oil pan.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



74. INSTALL TRANSAXLE HOUSING OIL SEAL


D025191E01
  1. Using SST and a hammer, drive in a new oil seal.

    Oil seal drive in depth:
    3.1 mm (0.122 in.)

    SST
    09517-12010  
    09630-24014   (09620-24051)

  1. Apply MP grease to the lip of the transaxle housing oil seal.



75. INSTALL TRANSAXLE CASE OIL SEAL


D025192E01
  1. Using SST and a hammer, drive in a new oil seal.

    SST
    09316-60011   (09316-00011)

    Oil seal drive in depth:
    3.1 mm (0.122 in.)

  1. Apply MP grease to the lip of the transaxle oil seal.



76. INSTALL OIL COOLER TUBE UNION


C059821
  1. Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them onto the 2 oil cooler tube unions.

  1. Install the 2 oil cooler tube unions onto the transaxle assembly.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



77. INSTALL BREATHER PLUG HOSE


C059820
  1. Install the breather plug hose onto the breather plug with the clamp.



78. INSTALL TRANSMISSION REVOLUTION SENSOR


C059782
  1. Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it onto the transmission revolution sensor.

  1. Install the transmission revolution sensor onto the transaxle assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



79. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C057491
  1. Provisionally fasten the neutral start switch with the 2 bolts.



    C057492
  1. Install the nut stopper and nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Provisionally install the control shaft lever.



    C057493
  1. Turn the control shaft lever counterclockwise until it stops, then turn it clockwise 2 notches.



    D025199
  1. Align the groove with the neutral basic line, and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C057495
  1. Using a screwdriver, stake the nut with the lock washer.



80. INSTALL TRANSMISSION CONTROL SHAFT LEVER


C057496
  1. Install the control lever, washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }