Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL SIDE GEAR


C060003
  1. Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with Toyota Genuine ATF Type T-IV, and install them onto the differential case.



2. INSTALL FRONT DIFFERENTIAL PINION SHAFT NO. 1


C060001
  1. Coat front differential pinion shaft No. 1 with Toyota Genuine ATF Type T-IV, and install it onto the differential case.



3. INSPECT BACKLASH


C060010
  1. Using a dial indicator, inspect the backlash of the side gear.

    Standard backlash:
    0.05 to 0.20 mm (0.0020 to 0.0079 in.)

    Thrust washer thickness:
    Mark
    Thickness
    -
    1.50 mm (0.0589 in.)
    -
    1.55 mm (0.0609 in.)
    -
    1.60 mm (0.0629 in.)
    -
    1.65 mm (0.0649 in.)
    -
    1.70 mm (0.0669 in.)
    -
    1.75 mm (0.0689 in.)



4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


C060005
  1. Using a 3 mm pin punch and hammer, install the pinion shaft straight pin.



    C060006
  1. Using a chisel and hammer, stake the differential case.



5. INSTALL FRONT DIFFERENTIAL RING GEAR


D025215
  1. Using Toyota Genuine ATF Type T-IV and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

  1. Clean the contact surface of the front differential case.



    C123274
  1. Aligh the matchmarks on the front differential ring gear and the differential case, and install the front differential ring gear case while it is still hot.



    C123275
  1. Tighten the 8 bolts.

    Torque:
    78 N*m{ 790 kgf*cm , 57 ft.*lbf }



6. INSTALL SPEEDOMETER DRIVE GEAR


C123273
  1. Install the speedometer drive gear onto the differential case.



7. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


C123276E01
  1. Using SST and a press, install the front differential case front tapered roller bearing (inner race) onto the differential case.

    SST
    09608-06041  



    D025217E01
  1. Using SST and a hammer, install the front differential case front tapered roller bearing (outer race) onto the transaxle housing.

    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)
    09950-60010   (09951-00340)



8. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


C123277E01
  1. Using SST and a press, install the front differential case rear tapered roller bearing (inner race) onto the differential case.

    SST
    09608-06041  



    D025219E01
  1. Using SST and a hammer, install the case washer and front differential case rear tapered roller bearing (outer race) onto the transaxle case.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)



9. INSTALL DIFFERENTIAL DRIVE PINION PLUG


C060013
  1. Using a 10 mm socket wrench and hammer, install a new differential drive pinion plug onto the differential drive pinion.

    Standard clearance:
    2.3 to 2.35 mm (0.090 to 0.093 in.)



10. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


D025220E01
  1. Using SST and a press, install the front drive pinion front tapered roller bearing (inner race) onto the differential drive pinion.



    D025227E01
  1. Using SST and a hammer, install the front drive pinion front tapered roller bearing (outer race) onto the transaxle housing.

    SST
    09608-04031  
    09950-60010   (09951-00540)
    09950-70010   (09951-07100)



11. INSTALL COUNTER DRIVE GEAR


D025228E01
  1. Using SST and a press, install the counter drive gear onto the differential drive pinion.

    SST
    09608-04031  
    09950-60010   (09951-00280)



12. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


D025229E01
  1. Using SST and a press, install the front drive pinion rear tapered roller bearing (inner race) onto the differential drive pinion.



    D025230E01
  1. Using SST and a hammer, install the pinion washer and front drive pinion rear tapered roller bearing (outer race) onto the transaxle case.

    SST
    09608-04031  
    09950-60010   (09951-00280, 09951-00600)
    09950-70010   (09951-07100)