Home › RESTRAINTS › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door Split Seat Type)

REAR SEAT OUTER BELT ASSEMBLY (for Hatchback 3 Door Split Seat Type) > INSTALLATION

for Preparation Click here


NOTICE:
Always use "TORX" socket wrench E10 when installing the rear seat.

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. INSTALL SEAT BELT HOLE SEAL


    B114436
  1. Engage the 2 claws and install the seat belt hole seal.



2. INSTALL REAR SEAT OUTER BELT ASSEMBLY


    B114437E01
  1. Check the angle of inclination required to lock the retractor.

    1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

      NOTICE:
      Do not disassemble the retractor.

      If the operation is not as specified, replace the rear seat outer belt.



    B114483
  1. Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



    B114482
  1. Install the through anchor with the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

  1. Check that the ELR locks.

    NOTICE:
    Perform the check with the rear seat outer belt installed.


    1. With the belt installed, check that the belt locks when it is pulled out quickly.
      If the operation is not as specified, replace the rear seat outer belt.



3. INSTALL ROOF SIDE INNER GARNISH


    B114504E01
  1. for RH Side (w/ Curtain Shield Airbag):

    1. for 3 Point Type Rear Center Seat Belt:

      1. Install a new special clip.
      2. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
      3. Engage the 4 clips and the claw and install the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Install a new special clip.
      2. Pass the rear seat outer belt through the slit in the roof side inner garnish.
      3. Engage the 4 clips and the claw and install the roof side inner garnish.



    B114505
  1. for RH Side (w/o Curtain Shield Airbag):

    1. for 3 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt and the rear center seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 4 clips and the claw and install the roof side inner garnish.

    2. for 2 Point Type Rear Center Seat Belt:

      1. Pass the rear seat outer belt through the slit in the roof side inner garnish.
      2. Engage the 4 clips and the claw and install the roof side inner garnish.



    B114506E01
  1. for LH Side (w/ Curtain Shield Airbag):

    1. Install a new special clip.

    2. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    3. Engage the 4 clips and the claw and install the roof side inner garnish.



    B114507
  1. for LH Side (w/o Curtain Shield Airbag):

    1. Pass the rear seat outer belt through the slit in the roof side inner garnish.

    2. Engage the 4 clips and the claw and install the roof side inner garnish.



4. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for 3 Point Type Rear Center Seat Belt)


    B114468
  1. Engage the 4 claws and install the center belt guide.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY


    B114501
  1. for RH Side:

    1. Engage the 3 clips and the 3 claws and install the deck trim side panel.

    2. Tighten the 3 screws.



    B114502
  1. for LH Side:

    1. w/ Luggage Compartment Room Light:

      1. Connect the luggage compartment room light connector.
      2. Engage the 3 clips and the 3 claws and install the deck trim side panel.
      3. Tighten the 3 screws.

    2. w/o Luggage Compartment Room Light:

      1. Engage the 3 clips and the 3 claws and install the deck trim side panel.
      2. Tighten the 3 screws.



    B114500
  1. Engage the clip and install the anchor plate of the rear seat outer belt.

  1. Tighten the bolt.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



6. INSTALL REAR DECK TRIM COVER


    B114283
  1. for Grand Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.



    B117692
  1. for Temper Spare Tire:

    1. Engage the 8 claws and install the rear deck trim cover.

    2. Install the 2 clips.



7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY


    B114499
  1. Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.



8. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (w/ Seat Belt Bar)


    B114759
  1. Install the front seat outer belt bar with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



9. INSTALL REAR SEAT SHOULDER BELT HANGER


    B117737
  1. Engage the 2 claws and install the rear seat shoulder belt hanger.



    B114498
  1. Install the belt of the rear seat outer belt.



10. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B114477
  1. Install the front door opening trim weatherstrip.



11. INSTALL FRONT DOOR SCUFF PLATE


    B114494
  1. Engage the 8 claws and install the front door scuff plate.



12. INSTALL REAR SEAT ASSEMBLY
  1. for RH Side:

    1. Install the rear seat assembly .

  1. for LH Side:

    1. Install the rear seat assembly .



13. INSTALL NO. 2 REAR SEAT LEG COVER (for LH Side)


    B114739
  1. Engage the 3 claws and install the No. 2 rear seat leg cover.



14. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover .



15. INSTALL DECK FLOOR BOX (w/ Deck Board)
  1. for RH Side:

    1. Install the deck floor box .

  1. for LH Side:

    1. Install the deck floor box.

      HINT:
      Use the same procedure as for the RH side.



16. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Install the spare wheel cover.



17. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106447
  1. Set the deck board and lock the 2 knobs.



18. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Install the rear floor carpet.



19. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Luggage Compartment Room Light)

Torque:
5.4 N*m{ 55 kgf*cm , 49 in.*lbf }