FRONT DRIVE SHAFT (for Sedan) > REASSEMBLY |
| 1. INSTALL FRONT DRIVE SHAFT DUST COVER |
![]() |
Using SST and a press, install a new dust cover into the inboard joint until it is flush with the end.
| 2. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING |
Install a new snap ring.
| 3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT |
Wrap the spline of the outboard joint shaft with protective tape.
Install new parts onto the outboard joint shaft in the following order.
Pack the joint portion of the outboard joint shaft and outboard joint boot with grease.
| Part No. | Quantity |
| 43410-52210 | 112 to 122 g (4.0 to 4.3 oz.) |
| 43420-52210 | |
| 43410-52201 | 90 to 100 g (3.2 to 3.5 oz.) |
| 43420-52201 |
Install the outboard joint boot onto the outboard joint shaft groove.
| 4. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP |
![]() |
Install the boot clamp onto the outboard joint boot and provisionally bend the lever.
![]() |
Lean your weight on your hand and roll the outboard joint forward while pressing the outboard joint against the work plane. Roll the outboard joint and fold the lever until a click sound can be heard.
![]() |
Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.
| 5. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
![]() |
Install the boot clamp onto the outboard joint boot and provisionally bend the lever.
![]() |
Using water pump pliers, pinch the boot clamp to provisionally fix it.
![]() |
Using a plastic hammer, tap the buckle to fix it while adjusting the clearance between the lever and the groove to make the clearances between the buckle edge and the lever end even.
| 6. INSTALL FRONT DRIVE SHAFT DAMPER (for RH Side) |
![]() |
Install the drive shaft damper onto dimension (A) shown in the illustration.
| Part No. | Dimension (A) |
| 43410-52210 | 425.6 to 429.6 mm (16.76 to 16.91 in.) |
| 43420-52210 | |
| 43410-52201 | 416.0 to 420.0 mm (16.38 to 16.54 in.) |
| 43420-52201 |
| 7. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (for RH Side) |
![]() |
Using needle-nose pliers, align the concave part with the protrusion of a new damper clamp in order to fix it.
| 8. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY |
Install new parts onto the outboard joint shaft in the following order.
Fix the outboard joint shaft in a vise between aluminum plates.
Remove the protective tape.
![]() |
Align the matchmarks and install the tripod joint onto the outboard joint shaft.
Using a brass bar and hammer, install the tripod joint.
![]() |
Using a snap ring expander, install a new snap ring.
Pack the inboard joint with grease.
| Part No. | Quantity |
| 43410-52210 | 125 to 135 g (4.4 to 4.8 oz.) |
| 43420-52210 | |
| 43410-52201 | 112 to 122 g (4.0 to 4.3 oz.) |
| 43420-52201 |
![]() |
Align the matchmarks and install the inboard joint onto the outboard joint shaft.
| 9. INSTALL FRONT AXLE INBOARD JOINT BOOT |
Install the inboard joint boot into the grooves of the inboard joint and outboard joint shaft.
| 10. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP |
![]() |
for One-touch Clamp Type:
Install the boot clamp onto the inboard joint boot and fix the boot clamp with a screwdriver.
![]() |
for Hook Clamp Type:
Using needle-nose pliers, align the concave part with the protrusion of the boot clamp in order to fix it.
| 11. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP |
![]() |
Adjust dimension (A) until it is within the specified length.
| Drive Shaft | Part No. | Dimension (A) |
| LH | 43420-52210 | 579.3 to 589.3 mm (22.81 to 23.20 in.) |
| 43420-52201 | 585.3 to 595.3 mm (23.04 to 23.44 in.) | |
| RH | 43410-52210 | 821.3 to 831.3 mm (32.33 to 32.73 in.) |
| 43410-52201 | 827.3 to 837.3 mm (32.57 to 32.96 in.) |
![]() |
for One-touch Clamp Type:
Install the boot clamp onto the inboard joint boot and fix the boot clamp with a screwdriver.
![]() |
for Hook Clamp Type:
Using needle-nose pliers, align the concave part with the protrusion of the boot clamp in order to fix it.
| 12. INSPECT FRONT DRIVE SHAFT |
![]() |
Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.
Check for cracks, damage and grease leakage on the boot joint.