Home › RESTRAINTS › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Driver Side Seat Belt Warning Light does not Operate

for Preparation Click here


DESCRIPTION

When the ignition switch to ON, the main body ECU communicates the status of the front seat inner belt (driver side) to the combination meter assembly using the CAN communication line. When the seat belt is unfastened, the combination meter assembly flashes the driver seat belt warning light on the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the warning light.

WIRING DIAGRAM


B120358E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (Indicat. Light D-seat Belt)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Perform the ACTIVE TEST according to the indication displayed on the tester.

    Combination Meter Assembly:

    Item
    Test Details
    Diagnostic Note
    Indicat. Lamp D-seat Belt
    Front driver seat belt warning light / OFF or ON
    -

    OK:
    Front driver seat belt warning light comes on



NG
REPLACE COMBINATION METER ASSEMBLY
OK


2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)


    B209386E01
  1. Disconnect the J35, J34 or J54 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    1 (E) - 2 (+)
    Tongue plate fastened
    10 kΩ or higher
    1 (E) - 2 (+)
    Tongue plate unfastened
    Below 1 Ω

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - MAIN BODY ECU)


    B209387E01
  1. Disconnect the J35, J34 or J54 front seat inner belt assembly (driver side) connector.

  1. Disconnect the D33 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Specified Condition
    D33-9 (DBKL) - J35-2 (+)*1
    Below 1 Ω
    D33-9 (DBKL) or J35-2 (+)*1 - Body ground
    10 kΩ or higher
    D33-9 (DBKL) - J34-2 (+)*2
    Below 1 Ω
    D33-9 (DBKL) or J34-2 (+)*2 - Body ground
    10 kΩ or higher
    D33-9 (DBKL) - J54-2 (+)*3
    Below 1 Ω
    D33-9 (DBKL) or J54-2 (+)*3 - Body ground
    10 kΩ or higher

    1. *1: LHD
    2. *2: Hatchback (RHD)
    3. *3: Sedan (RHD)

  1. Reconnect the front seat inner belt assembly (driver side) connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - BODY GROUND)


    B209388E01
  1. Disconnect the J35, J34 or J54 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Specified Condition
    J35-1 (E)*1 - Body ground
    Below 1 Ω
    J34-1 (E)*2 - Body ground
    Below 1 Ω
    J54-1 (E)*3 - Body ground
    Below 1 Ω

    1. *1: LHD
    2. *2: Hatchback (RHD)
    3. *3: Sedan (RHD)

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU