Home › RESTRAINTS › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

When the ignition switch to ON and the passenger seat is occupied, the occupant detection sensor communicates the status of the front seat inner belt assembly (passenger side) to the combination meter assembly. When the front seat belt is unfastened, the combination meter assembly flashes the front passenger seat belt warning light on the instrument panel cluster finish panel end*1 or hazard warning signal switch assembly*2. When the seat belt is fastened, the combination meter stops flashing the front passenger seat belt warning light.

HINT:
*1: Hatchback
*2: Sedan


WIRING DIAGRAM


B209389E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (Indicat. Lamp P-seat Belt)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Perform the ACTIVE TEST according to the indication displayed on the tester.

    Combination Meter Assembly:

    Item
    Test details
    Diagnostic Note
    Indicat. Lamp P-seat Belt
    Front passenger seat belt warning light/ OFF or ON
    -

    OK:
    Front passenger seat belt warning light comes on.



NG
Go to step 4
OK


2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)


    B120593E03
  1. Disconnect the J34 or J35 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the occupant detection sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E) - Occupant detection sensor connector-1
    Tongue plate fastened
    10 kΩ or higher
    1 (E) - Occupant detection sensor connector-1
    Tongue plate unfastened
    Below 1Ω
    1 (E) - Body ground
    Always
    10 kΩ or higher
    Occupant detection sensor connector-1 - Body ground
    Always
    10 kΩ or higher
    2 (+) - Occupant detection sensor connector-3
    Always
    Below 1Ω
    2 (+) or Occupant detection sensor connector-3 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the front seat inner belt assembly (passenger side) connector.

  1. Reconnect the occupant detection sensor connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)
OK


3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - COMBINATION METER, BODY GROUND)


    B141565E01
  1. Disconnect the J34 or J35 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the D1 combination meter assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J34-2 (+)*1 - D1-10 (P/SB)
    Below 1 Ω
    J34-2 (+)*1 or D1-10 (P/SB) - Body ground
    10 kΩ or higher
    J34-1 (E)*1 - Body ground
    Below 1 Ω
    J35-2 (+)*1 - D1-10 (P/SB)
    Below 1 Ω
    J35-2 (+)*1 or D1-10 (P/SB) - Body ground
    10 kΩ or higher
    J35-1 (E)*1 - Body ground
    Below 1 Ω

    1. *1: LHD
    2. *2: RHD

  1. Reconnect the front seat inner belt assembly (passenger side) connector.

  1. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OCCUPANT DETECTION SENSOR 

4.INSPECT FUSE (GAUGE)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Remove the GAUGE fuse.



NG
REPLACE FUSE
OK


5.CHECK HARNESS AND CONNECTOR (FUSE - FRONT PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY)


    B209390E01
  1. Hatchback:

    1. Disconnect the D27 or D59 front passenger seat belt warning light connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4S-15 - D27-6 (IG+)*1
      Below 1 Ω
      4S-15 or D27-6 (IG+)*1 - Body ground
      10 kΩ or higher
      4S-15 - D59-1 (IG+)*2
      Below 1 Ω
      4S-15 or D59-1 (IG+)*2 - Body ground
      10 kΩ or higher

      1. *1: w/ Airbag Cut Off Switch
      2. *2: w/o Airbag Cut Off Switch

    4. Reconnect the front passenger seat belt warning light and main body ECU connectors.



    B209391E01
  1. Sedan:

    1. Disconnect the D85 hazard warning signal switch assembly connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4S-15 - D85-6 (IG+)
      Below 1 Ω
      4S-15 or D85-6 (IG+) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SEAT BELT WARNING LIGHT - COMBINATION METER, BODY GROUND)


    B209392E01
  1. Hatchback:

    1. Disconnect the D27 or D59 front passenger seat belt warning light connector.

    2. Disconnect the D87 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      LHD:
      Tester Connection
      Specified Condition
      D27-3 (PBEW)*1 - D87-9 (PBLT)
      Below 1 Ω
      D27-3 (PBEW)*1 - D87-9 (PBLT) - Body ground
      10 kΩ or higher
      D59-3 (PBEW)*2 - D87-9 (PBLT)
      Below 1 Ω
      D59-3 (PBEW)*2 - D87-9 (PBLT) - Body ground
      10 kΩ or higher

      1. *1: w/ Airbag Cut Off Switch
      2. *2: w/o Airbag Cut Off Switch

      Standard resistance:
      RHD:
      Tester Connection
      Specified Condition
      D27-3 (PBEW)*1 - D87-16 (PBLT)
      Below 1 Ω
      D27-3 (PBEW)*1 or D87-16 (PBLT) - Body ground
      10 kΩ or higher
      D59-3 (PBEW)*2 - D87-16 (PBLT)
      Below 1 Ω
      D59-3 (PBEW)*1 or D87-16 (PBLT) - Body ground
      10 kΩ or higher

      1. *1: w/ Airbag Cut Off Switch
      2. *2: w/o Airbag Cut Off Switch

    4. Reconnect the front passenger seat belt warning light and combination meter connectors.



    B209393E01
  1. Sedan:

    1. Disconnect the D85 hazard warning signal switch assembly connector.

    2. Disconnect the D84 combination meter assembly connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D85-8 (PBEW) - D84-9 (PBLT)
      Below 1 Ω
      D85-8 (PBEW) or D84-9 (PBLT) - Body ground
      10 kΩ or higher

    4. Reconnect the front passenger seat belt warning light and combination meter connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT ASSEMBLY


    B127790E03
  1. Hatchback (w/ Airbag Cut Off Switch):

    1. Remove the front passenger seat belt warning light assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 6 (lG+) Negative battery - Terminal 3 (PBEW)
      Front passenger seat belt warning light illuminates

    3. Reinstall the front passenger seat belt warning light assembly.



    B127791E02
  1. Hatchback (w/o Airbag Cut Off Switch):

    1. Remove the front passenger seat belt warning light assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 1 (lG+) Negative battery - Terminal 3 (PBEW)
      Front passenger seat belt warning light Illuminates

    3. Reinstall the front passenger seat belt warning light assembly.



    B143252E01
  1. Sedan:

    1. Remove the hazard warning signal switch assembly.

    2. Apply battery voltage to the terminals and check that the front passenger seat belt warning light illuminates.

      Standard:
      Measurement Condition
      Specified Condition
      Positive battery - Terminal 6 (lG+) Negative battery - Terminal 8 (PBEW)
      Front passenger seat belt warning light Illuminates

    3. Reinstall the front passenger seat belt warning light assembly.



NG
REPLACE FRONT PASSENGER SEAT BELT WARNING LIGHT
OK

REPLACE COMBINATION METER ASSEMBLY