Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR (for Hatchback Front Side)

POWER WINDOW REGULATOR MOTOR (for Hatchback Front Side) > INSTALLATION

for Preparation Click here



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT


B127222E01
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor assembly front with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B116828E01
  1. Loosely screw bolt A onto the front door window regulator.

  1. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the front door window regulator with the 5 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B116847
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.



    B116825
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL FRONT DOOR SERVICE HOLE COVER


B116848E01
  1. for 5 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0mm (0.079 in.) or more
    B
    6.0mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B116849E01
  1. for 3 Door:
    Apply butyl tape to the door panel, then install the front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0mm (0.079 in.) or more
    B
    6.0mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



5. INSTALL FRONT DOOR BELT MOULDING


    B114401
  1. for 5 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.



    2. B114397E02
    3. Remove the protective tape.



    B114614
  1. for 3 Door:

    1. Engage the 5 claws and the clip and install a new front door belt moulding.



    2. B114612E01
    3. Remove the protective tape.



6. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY


B118045
  1. Engage the claw, then install the outer rear view mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Power mirror:
    Connect the connector.



7. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)


    B114606E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame rear moulding.
    Tape size: 
    Area
    t
    W
    H
    A
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    340 mm (13.386 in.)
    B
    0.8 mm (0.032 in.)
    5 mm (0.197 in.)
    376 mm (14.803 in.)



    B114607
  1. Engage the 2 clips and the claw and install the front door window frame rear moulding.



8. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING


    B127706E01
  1. Clean the attachment surface.

    1. Using an infrared light, heat the adhesive remaining on the body.

      NOTICE:
      Do not burn yourself with the heated body or infrared light.

    2. Using a shop rag or piece of cloth, rub the remaining adhesive off the body.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Apply new double-sided adhesive tape to the front door window frame front moulding.
    Tape size: 
    Area
    t
    W
    H
    A
    1.2 mm (0.047 in.)
    7 mm (0.276 in.)
    88 mm (3.465 in.)



    B127705E01
  1. Engage the 2 clips and the claw and install the front door window frame front moulding.



9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B127219
  1. Connect the front door lock remote control cable and front door inside locking cable.



    B116821
  1. 5 Door:
    Engage the 8 clips and install the front door trim board.



    B116822
  1. 3 Door:
    Engage the 9 clips and install the front door trim board.



    B107840
  1. Tighten the 4 screws.



10. INSTALL FRONT ARMREST BASE PANEL UPPER


B116819
  1. Connect the connector.

  1. Engage the 5 claws and clip and install the front armrest base panel upper.



11. INSTALL DOOR ARMREST COVER


B116818
  1. for 5 Door:
    Engage the 8 claws and 3 clips and install the door armrest cover.



    B116851
  1. for 3 Door:
    Engage the 12 claws and 4 clips and install the door armrest cover.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }