Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR (for Hatchback Front Side)

POWER WINDOW REGULATOR MOTOR (for Hatchback Front Side) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE DOOR ARMREST COVER


B116818
  1. for 5 Door:
    Using a screwdriver with its tip wrapped in protective tape, disengage the 8 claws and 3 clips and remove the door armrest cover.



    B116851
  1. for 3 Door:
    Disengage the 12 claws and 3 clips and remove the door armrest cover.



3. REMOVE FRONT ARMREST BASE PANEL UPPER


B116819
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 5 claws and clip and remove the front armrest base panel upper.

  1. Disconnect the connector.



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


B107840
  1. Remove the 4 screws.



    B116821
  1. 5 Door:
    Disengage the 8 clips.



    B116822
  1. 3 Door:
    Disengage the 9 clips.



    B127219
  1. Disconnect the front door lock remote control cable and front door inside locking cable and remove the front door trim board.



5. REMOVE FRONT DOOR WINDOW FRAME FRONT MOULDING


    B127705E01
  1. Using an infrared light, heat the front door window frame front moulding.

    CAUTION:
    Do not burn yourself with the heated front door panel or infrared light.

    HINT:
    Heat at 40 to 60 °C (104 to 140 °F) for 3 to 5 minutes.

  1. Disengage the 2 claws and remove the double-sided adhesive tape and the front door window frame front moulding.



6. REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)


    B114605E01
  1. Using an infrared light, heat the front door window frame rear moulding.

    NOTICE:
    Do not burn yourself with the heated front door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 3 to 5 minutes.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 clips and the claw and remove the double-sided adhesive tape and front door window frame rear moulding.



7. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


B118045
  1. w/ Power mirror:
    Disconnect the connector.

  1. Remove the 3 nuts, disengage the claw and remove the outer rear view mirror.



8. REMOVE FRONT DOOR BELT MOULDING


    B114397E02
  1. for 5 Door:

    1. Apply protective tape to the door panel in the area around the front door belt moulding.



    2. B114398E02
    3. Using a moulding remover, disengage the 5 claws and the clip and remove the front door belt moulding.



    B114612E01
  1. for 3 Door:

    1. Apply protective tape to the door panel in the area around the front door moulding.



    2. B114613E01
    3. Using a moulding remover, disengage the 5 claws and remove the front door belt moulding.



9. REMOVE FRONT DOOR SERVICE HOLE COVER


B116823
  1. for 5 Door:
    Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



    B116824
  1. for 3 Door:
    Disconnect the connectors and clamps, then remove the front door service hole cover.

    NOTICE:
    Remove any tape remaining on the door side.



10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Driver side:
    Provisionally install the power window regulator master switch.

  1. Passenger side:
    Provisionally install the power window regulator switch.



    B116825
  1. Move the front door glass until the 2 bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass when removing the bolts.



    B116827
  1. Remove the front door glass in the direction indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.

  1. Driver side:
    Remove the power window regulator master switch.

  1. Passenger side:
    Remove the power window regulator switch.



11. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


B116828E01
  1. Disconnect the connector.

  1. Loosen bolt A.

  1. Remove the 5 bolts, then remove the front door window regulator.

    NOTICE:
    Do not drop or damage the window regulator when removing the bolts.

    HINT:
    Remove the window regulator through the service hole.



12. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT


B127222E01
  1. Using "Torx" socket wrench T25, remove the 3 screws and the power window regulator motor.