Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR (for Hatchback Rear Side)

POWER WINDOW REGULATOR MOTOR (for Hatchback Rear Side) > INSTALLATION

for Preparation Click here



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


B116929
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B116928E01
  1. Loosely screw bolt A onto the rear door window regulator.

  1. Insert the rear door window regulator into the door panel. Use bolt A to hang the rear door window regulator on the door panel.

    NOTICE:
    Do not drop the window regulator as it may be damaged.

  1. Install the rear door window regulator with the 4 bolts, and tighten bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


B116927
  1. Install the rear door glass onto the rear door window regulator.



4. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP
  1. Install the rear door quarter window glass onto the rear door quarter window weatherstrip.



    B116926
  1. Slide the rear door quarter window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.



5. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


B116924
  1. Install the rear door window division bar with the 2 bolts and screw.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



6. INSTALL REAR DOOR GLASS RUN


B116877
  1. Install the rear door glass run.



7. INSTALL REAR DOOR BELT MOULDING


    B114406
  1. Engage the 5 claws and the clip and install a new rear door belt moulding.



    B114404E01
  1. Remove the protective tape.



8. INSTALL REAR DOOR WEATHERSTRIP


B116876
  1. Engage the 32 clips and install the rear door weatherstrip.



9. INSTALL REAR DOOR CHECK ASSEMBLY


B116875
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the rear door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the rear door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. INSTALL REAR DOOR SERVICE HOLE COVER


B116873E01
  1. w/ Rear speaker:
    Apply butyl tape to the door panel, then install the rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



    B116874E01
  1. w/o Rear speaker:
    Apply butyl tape to the door panel, then install the rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.



11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


B116868
  1. Connect the rear door lock remote control cable and rear door inside locking cable.

  1. Connect the connector.



    B116867
  1. Engage the 7 clips and install the rear door trim board.



    B116866
  1. Tighten the 2 screws.



    B116865
  1. Engage the 3 claws and install the rear door armrest plug.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }