Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SIDE AIRBAG SENSOR (for Hatchback 3 Door)

SIDE AIRBAG SENSOR (for Hatchback 3 Door) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.



3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106371
  1. Release the 2 knobs and remove the deck board.



4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Remove the spare wheel cover.



5. REMOVE DECK FLOOR BOX RH (w/ Deck Board)


    B106372
  1. Release the 2 knobs and remove the deck floor box.



6. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.



7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Remove the rear floor carpet.



8. REMOVE NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Remove the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Remove the No. 1 rear seat leg cover .



9. REMOVE NO. 2 REAR SEAT LEG COVER


    B126921E01
  1. Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.



10. REMOVE REAR SEAT ASSEMBLY RH


    B114660
  1. Using "TORX" socket wrench E10, remove the 2 bolts and pull up the rear seat cushion.



    B119885
  1. Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.



11. REMOVE REAR SEAT ASSEMBLY LH


    B114740
  1. Using "TORX" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.



    B117760
  1. Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.



12. REMOVE FRONT DOOR SCUFF PLATE RH


    B114494
  1. Disengage the 8 claws and remove the front door scuff plate.



13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B114286
  1. Remove the front door opening trim weatherstrip to the extent necessary to remove the quarter trim panel assembly front RH.



14. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY RH (for Sill Bar Type)


    B114759
  1. Remove the 2 bolts and the front seat outer belt bar.



15. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH


    B114498
  1. Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.



    B114499
  1. Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.



16. REMOVE SIDE AIRBAG SENSOR ASSEMBLY

CAUTION:
Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.



    B106572E01
  1. Slide the outer housing and detach the airbag connector.



    B106573E01
  1. Remove the bolt, disengage the hook and remove the side airbag sensor.