Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB (for Sedan)

FRONT AXLE HUB (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AXLE ASSEMBLY


    C125277
  1. Install the front axle assembly onto the shock absorber.

  1. Install the 2 bolts and 2 nuts.

    Torque:
    164 N*m{ 1,672 kgf*cm , 121 ft.*lbf }

    HINT:
    Keep the nut from rotating while turning the bolt.

  1. Push the front axle out of the vehicle to align the spline of the drive shaft with the front axle and insert the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Check for any foreign matter on the speed sensor rotor and insertion part.
    4. Do not damage the speed sensor rotor.



2. INSTALL FRONT SUSPENSION LOWER ARM


    C107513
  1. Install the lower arm onto the steering knuckle with a new castle nut.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new clip.



3. INSTALL FRONT STABILIZER LINK ASSEMBLY


    C106044
  1. Install the stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.



4. INSTALL TIE ROD END SUB-ASSEMBLY


    C107961
  1. Install the tie rod end onto the steering knuckle with a new castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut by a further turn of up to 60°.

  1. Install a new cotter pin.



5. INSTALL FRONT DISC


C108932E01
  1. Align the matchmarks of the disc and axle hub and install the disc.

    NOTICE:
    When replacing the disc, select the position that gives the minimum disc runout.



6. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


C085618
  1. Install the disc brake caliper onto the steering knuckle.

    Torque:
    107 N*m{ 1,089 kgf*cm , 79 ft.*lbf }



7. INSTALL FRONT SPEED SENSOR (w/ ABS)


    C112274
  1. Install the speed sensor onto the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Check that the speed sensor tip and installation portion are free of foreign matter.
    2. Install the speed sensor without turning it from its original installation angle.



    C125274
  1. Install the flexible hose and speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Install the flexible hose and speed sensor without twisting them.



8. INSTALL FRONT AXLE HUB NUT


    C057566
  1. Using a 30 mm socket wrench, install a new axle hub nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 160 ft.*lbf }

  1. Using a chisel and hammer, stake the axle hub nut.



9. INSPECT FRONT AXLE HUB BEARING
  1. Remove the front wheel.

  1. Separate the disc brake caliper .

  1. Remove the front disc .



    C107912
  1. Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the bearing.



    C107911
  1. Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout exceeds the maximum, replace the bearing and axle hub.

  1. Install the front disc .

  1. Install the disc brake caliper .

  1. Install the front wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



10. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



13. CHECK ABS SENSOR SIGNAL (w/o VSC)
  1. Check the ABS sensor signal (Click here).



14. CHECK ABS SENSOR SIGNAL (w/ VSC)
  1. Check the ABS sensor signal (Click here).