Home › ENGINE ยท 1NZ-FE › EXHAUST › EXHAUST PIPE

EXHAUST PIPE > INSTALLATION

for Preparation Click here



1. INSTALL EXHAUST PIPE ASSEMBLY TAIL


A137397E01
  1. Check the No. 4 exhaust pipe supports.

    NOTICE:
    Install No. 4 exhaust pipe support onto the pipe retaining support.



  1. Install the 2 No. 4 exhaust pipe supports and the exhaust tail pipe assembly. (for Hatchback)


    A115390



  1. Install the 3 No. 4 exhaust pipe supports and the exhaust tail pipe assembly. (for Sedan)


    A133340



2. INSTALL EXHAUST PIPE ASSEMBLY FRONT


A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front side):
    40.5 mm (1.594 in.)

    Minimum length (Rear side):
    38.5 (1.516 in.)

    If the length is not as specified, replace the compression spring.



    A104635E01
  1. Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 No. 4 exhaust pipe supports.



  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }



    A119126



3. INSTALL HEATED OXYGEN SENSOR


A115424E01
  1. Using SST, install the sensor onto the front exhaust pipe.

    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. Pass the sensor connector through the floor panel and install the grommet.

  1. Connect the sensor connector.



4. INSTALL CONSOLE BOX ASSEMBLY REAR (for Hatchback)


C116873
  1. Engage the 2 clips and install the console box with the bolt.



5. INSTALL INSTRUMENT PAD LOWER LH (for Sedan)


    B132339
  1. Engage the claw and 3 clips and install the instrument pad lower.

  1. Install screw <I>.



6. INSTALL CONSOLE BOX ASSEMBLY REAR (for Sedan)


    B132349
  1. Engage the 4 claws and install the rear console box.

  1. Install the 2 bolts and 2 screws.

  1. Connect the clamp.



7. INSTALL CONSOLE BOX COVER REAR (for Hatchback)


C109006E01
  1. Engage the 8 claws to install the console box rear cover.



8. INSTALL CONSOLE BOX CARPET (for Sedan)


    B132346
  1. Install the console box carpet.



9. INSTALL CONSOLE PANEL SUB-ASSEMBLY UPPER (for Sedan)


    B132348
  1. Connect the connector.

  1. Engage the 3 clips and 3 claws and install the console upper rear panel.



10. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (for Sedan)


    B132347
  1. Engage the 5 clips and the claw and install the upper console panel.



11. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)


C109005E01
  1. Engage the 6 claws to install the shifting hole cover.



12. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132388
  1. Install the shift lever knob.



13. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (for Sedan)


B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.



14. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (for Sedan)


B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.



15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



16. CHECK FOR EXHAUST GAS LEAKAGE