Home › BRAKE › BRAKE › BRAKE MASTER CYLINDER (for Hatchback LHD)

BRAKE MASTER CYLINDER (for Hatchback LHD) > INSTALLATION

for Preparation Click here



1. INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD


G028332E02
  1. Set SST on the master cylinder and lower the rod of SST until it just touches the piston.

    SST
    09737-00013  

    HINT:
    SST: 09737-00012 can also be used.

  1. Apply chalk to the flat tip of the SST rod. Turn SST upside down and measure the clearance between the brake booster push rod and SST.

    Standard Clearance:
    -0.21 to 0 mm (-0.0083 to 0 in.)

    If there is clearance between the SST main body and the shell of the brake booster, the push rod is protruding too far. If the chalk does not stick to the tip of the brake booster push rod, the push rod protrusion is insufficient.



    F047969E04
  1. If the clearance is not within the standard, adjust the length by holding the rod using SST and turning the tip of the rod using a 7 mm socket driver.

    SST
    09737-00020  

    NOTICE:
    Check the push rod clearance again after adjusting.



2. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Install a new O-ring onto the brake master cylinder sub-assembly.



    C116934
  1. w/ ABS:

    1. Install the brake master cylinder sub-assembly with the 2 nuts.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C121833
  1. w/o ABS:

    1. Install the brake master cylinder sub-assembly and brake tube way with the 2 nuts.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    C121690E01
  1. Using SST, install the 2 brake tubes onto the brake master cylinder sub-assembly.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.



    C121832E01
  1. w/o ABS:

    1. Using SST, install the 3 brake tubes to the brake tube way.

      SST
      09023-00100  

      Torque:
      for use without SST:
      15 N*m{ 155 kgf*cm , 11 ft.*lbf }
      for use with SST:
      14 N*m{ 143 kgf*cm , 10 ft.*lbf }

      HINT:
      1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      2. This torque value is effective when SST is parallel to a torque wrench.

  1. Connect the brake fluid level warning switch connector.



3. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)


C116933
  1. Connect the reservoir tube with the clip.



4. INSTALL BATTERY CARRIER

Torque:
17 N*m{ 175 kgf*cm , 13 ft.*lbf }



5. INSTALL BATTERY TRAY


6. INSTALL BATTERY


7. FILL RESERVOIR WITH BRAKE FLUID


C116908E01
  1. LHD:

    1. Disengage the 3 clips and separate the hood to cowl top seal.

    2. Remove the cowl top ventilator louver.

  1. RHD:

    1. Disengage the 2 clips and separate the hood to cowl top seal.

    2. Remove the cowl top ventilator louver.



    C116909E01
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



8. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C116910E02
  1. Using a union nut wrench (10 mm), disconnect the brake tubes from the master cylinder.



    C116911E01
  1. Slowly depress the brake pedal and hold it there (Step A).



    C116912E01
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C116910E02
  1. Using a union nut wrench (10 mm), connect the brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



9. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    Front Disc and Rear Drum Brake:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Rear Disc Brake:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



10. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



11. CHECK FOR BRAKE FLUID LEAKAGE