Home › BRAKE › BRAKE › BRAKE BOOSTER (for Sedan RHD)

BRAKE BOOSTER (for Sedan RHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY


C107598
  1. Install the grommet onto the brake booster.

  1. Install the vacuum check valve onto the brake booster.



2. INSTALL BRAKE BOOSTER
  1. Install a new gasket onto the brake booster.



    C107597
  1. Install the brake booster with the 4 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the wire harness clamp.



    C107596
  1. Install the wire harness bracket with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C107595
  1. Connect the vacuum hose to the vacuum check valve with the clip.



3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS


C107594
  1. Provisionally install the push rod clevis onto the brake booster.

    HINT:
    Tighten the push rod lock nut when adjusting the brake pedal height.

  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Install the push rod clevis onto the brake pedal with the push rod pin and clip.

  1. Install the return spring.



4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER


C107593
  1. Install a new stop light switch mounting adjuster onto the pedal support.



5. INSTALL STOP LIGHT SWITCH


F049043E01
  1. Insert the stop light switch into the adjuster until it just touches the brake pedal.

    NOTICE:
    Do not depress the brake pedal.



    F049044E08
  1. Make a quarter turn clockwise to install the stop light switch.

    NOTICE:
    Do not depress the brake pedal.

    HINT:
    The turning torque for installing the stop light switch:

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

  1. Check the stop light switch clearance.

    Stop light switch clearance:
    0.5 to 2.6 mm (0.020 to 0.102 in.)

  1. Connect the connector to the stop light switch.



6. INSTALL INSTRUMENT PANEL UNDER TRAY


B132333
  1. Engage the 6 claws and install the instrument panel under tray.

  1. Install the 2 <A> screws.



    B132390
  1. Engage the 4 claws and install the instrument panel under tray.



7. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Install a new O-ring onto the brake master cylinder sub-assembly.



    C107587
  1. Install the brake master cylinder sub-assembly with the 2 nuts.

    Torque:
    18 N*m{ 180 kgf*cm , 13 ft.*lbf }



    C107586E01
  1. Using SST, install the 2 brake tubes onto the brake master cylinder sub-assembly.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.

  1. Connect the brake fluid level warning switch connector.



8. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)


C107585
  1. Connect the reservoir tube with the clip.



9. INSTALL COWL TOP PANEL OUTER


A128448
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128447
  1. Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 57 in.*lbf }



    A128446
  1. Connect the wire harness clamp.



10. INSTALL FRONT AIR SHUTTER SEAL


A133324
  1. Engage the 3 claws to install the front air shutter seal.



11. INSTALL FRONT WIPER MOTOR AND LINK


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



12. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127836
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127835
  1. Engage the 10 hooks and the 6 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



13. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



14. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



17. INSTALL FRONT WIPER ARM HEAD CAP


    E127841
  1. Engage the claw and install the 2 front wiper arm head caps.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



19. FILL RESERVOIR WITH BRAKE FLUID


C133125E02
  1. Remove the cowl top No. 2 ventilator louver center.



    C133126E01
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



20. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C116910E02
  1. Using a union nut wrench (10 mm), disconnect the brake tubes from the master cylinder.



    C116911E01
  1. Slowly depress the brake pedal and hold it there (Step A).



    C116912E01
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C116910E02
  1. Using a union nut wrench (10 mm), connect the brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



21. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



22. BLEED BRAKE ACTUATOR (w/ VSC)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, perform air bleeding of the brake actuator with the intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the engine off.

  1. Connect the intelligent tester to the DLC3, and turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Select "Air Bleeding" on the intelligent tester.

    HINT:
    Refer to the tester operator's manual for further details.



  1. Bleed the air out of the brake line when Step 1:
    Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.




      C116913
    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step E).

    3. When fluid stops coming out, tighten the bleeder plug and release the brake pedal (Step F).

    4. Repeat Steps E and F until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    6. Repeat the above procedure for each wheel to bleed the air out of the brake line.

  1. Bleed the air out of the suction line when Step 2:
    Inhalation appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect the vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator to bleed the air using the intelligent tester (Step G).

      NOTICE:
      Release the brake pedal at this time.

      HINT:
      This operation stops automatically after 4 seconds.

    3. Check if the operation has stopped by referring to the intelligent tester display and tighten the bleeder plug (Step H).

    4. Repeat Steps G and H until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

  1. Bleed the air out of the pressure reduction line when Step 3: Decrease appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (Step I).

    3. Using the intelligent tester, operate the brake actuator assembly, completely depress the brake pedal and hold it there (Step J).

      NOTICE:
      1. During this procedure, the pedal will feel heavy, but completely depress it so that the brake fluid comes out of the bleeder plug.
      2. Hold the brake pedal depressed. Do not depress and release the pedal repeatedly.

      HINT:
      1. The operation stops automatically after 4 seconds. When performing this procedure continuously, set an interval of at least 20 seconds.
      2. When the operation is complete, the brake pedal goes down slightly. This is a normal phenomenon caused when the solenoid opens.

    4. Tighten the bleeder plug, and then release the brake pedal (Step K).

    5. Repeat Steps I to K until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    7. Repeat the above procedure for the other wheels to bleed the air out of the brake line.



  1. Bleed the air out of the brake line again when Step 4: Increase appears on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Make sure that the master cylinder reservoir tank does not become empty.




      C116913
    1. Connect the vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (Step L).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step M).

    4. Repeat Steps L and M until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

    6. Repeat the above procedure for the other wheels to bleed the air out of the brake line.

    7. Make sure that the air bleeding is complete by referring to the intelligent tester display and turn off the intelligent tester.

    8. Disconnect the intelligent tester from the DLC3.

    9. Turn the ignition switch off.



23. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



24. CHECK FOR BRAKE FLUID LEAKAGE


25. INSPECT AND ADJUST BRAKE PEDAL
  1. Remove the instrument panel under tray .



    C116874E01
  1. Inspect the brake pedal height.

    Pedal height from floor:
    w/ABS
    w/o ABS
    107.3 to 117.3 mm
    (4.224 to 4.618 in.)
    107.8 to 117.8 mm
    (4.244 to 4.638 in.)

    If the pedal height is incorrect, adjust it.



  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor:
      w/ABS
      w/o ABS
      107.3 to 117.3 mm
      (4.224 to 4.618 in.)
      107.8 to 117.8 mm
      (4.244 to 4.638 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    6. F049043E01
    7. Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.



    8. F049044E08
    9. Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    10. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    11. Connect the connector to the stop light switch.



    F048932E01
  1. Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.



    R000934E02
  1. Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor at 300 N (31 kgf, 67.4 lbf):

      LHD
      RHD
      w/ ABS
      More than 73 mm (2.87 in.)
      More than 74 mm (2.91 in.)
      w/o ABS
      More than 70 mm (2.75 in.)
      -

      HINT:
      Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

      If incorrect, troubleshoot the brake system.

  1. Install the instrument panel under tray .