Home › BRAKE › BRAKE › BRAKE BOOSTER (for Sedan RHD)

BRAKE BOOSTER (for Sedan RHD) > REMOVAL

for Preparation Click here


NOTICE:
Release the vacuum from booster by depressing the brake pedal several times.
Then remove the brake master cylinder from brake booster.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.



3. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127835
  1. Disengage the 2 clips, the 6 claws and the 10 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127836
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



9. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



10. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



11. REMOVE COWL TOP PANEL OUTER


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



12. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)


C107585
  1. Slide the clip and disconnect the reservoir tube.



13. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Disconnect the brake fluid level warning switch connector.



    C107586E01
  1. Using SST, separate the 2 brake tubes from the brake master cylinder sub-assembly.

    SST
    09023-00100  



    C107587
  1. Remove the 2 nuts and remove the brake master cylinder sub-assembly.

  1. Remove the O-ring from the brake master cylinder sub-assembly.

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. Release the vacuum from booster by depressing the brake pedal several times. Then remove the brake master cylinder from brake booster.
    4. When installing the brake master cylinder sub-assembly onto the brake booster, or when removing the brake master cylinder sub-assembly from the brake booster, make sure that the brake master cylinder sub-assembly is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling off.
    5. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the piston.
    6. Do not use any other type of grease or fluid.



14. REMOVE INSTRUMENT PANEL UNDER TRAY


B132341
  1. Disengage the 4 claws and open the instrument panel under tray.



    B132333
  1. Remove the 2 <A> screws.

  1. Disengage the 6 claws and remove the instrument panel under tray.



15. REMOVE STOP LIGHT SWITCH


C107592
  1. Disconnect the connector from the stop light switch.

  1. Turn the stop light switch counterclockwise, and remove the stop light switch.



16. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER


C107593
  1. Remove the stop light switch mounting adjuster from the pedal support.



17. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS


C107594
  1. Remove the brake pedal return spring.

  1. Loosen the push rod lock nut.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.

  1. Remove the push rod clevis from the brake booster.



18. REMOVE BRAKE BOOSTER


C107595
  1. Slide the clip and disconnect the vacuum hose from the check valve.



    C107596
  1. Remove the bolt and separate the wire harness bracket.



    C107597
  1. Remove the wire harness clamp and 4 nuts and remove the brake booster.

  1. Remove the gasket from the brake booster.



19. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY


C107598
  1. Remove the vacuum check valve from the brake booster.

  1. Remove the grommet from the brake booster.