BRAKE BOOSTER (for Sedan RHD) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN BRAKE FLUID |
| 3. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| 6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
| 7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Disengage the 2 clips, the 6 claws and the 10 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 9. REMOVE FRONT WIPER MOTOR AND LINK |
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 10. REMOVE FRONT AIR SHUTTER SEAL |
![]() |
Disengage the 3 claws and remove the front air shutter seal.
| 11. REMOVE COWL TOP PANEL OUTER |
![]() |
Disengage the wire harness clamp.
![]() |
Remove the 2 bolts and remove the cowl top to cowl inner brace.
![]() |
Remove the 8 bolts and remove the cowl top panel outer.
| 12. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle) |
![]() |
Slide the clip and disconnect the reservoir tube.
| 13. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY |
Disconnect the brake fluid level warning switch connector.
![]() |
Using SST, separate the 2 brake tubes from the brake master cylinder sub-assembly.
![]() |
Remove the 2 nuts and remove the brake master cylinder sub-assembly.
Remove the O-ring from the brake master cylinder sub-assembly.
| 14. REMOVE INSTRUMENT PANEL UNDER TRAY |
![]() |
Disengage the 4 claws and open the instrument panel under tray.
![]() |
Remove the 2 <A> screws.
Disengage the 6 claws and remove the instrument panel under tray.
| 15. REMOVE STOP LIGHT SWITCH |
![]() |
Disconnect the connector from the stop light switch.
Turn the stop light switch counterclockwise, and remove the stop light switch.
| 16. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER |
![]() |
Remove the stop light switch mounting adjuster from the pedal support.
| 17. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Remove the brake pedal return spring.
Loosen the push rod lock nut.
Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.
Remove the push rod clevis from the brake booster.
| 18. REMOVE BRAKE BOOSTER |
![]() |
Slide the clip and disconnect the vacuum hose from the check valve.
![]() |
Remove the bolt and separate the wire harness bracket.
![]() |
Remove the wire harness clamp and 4 nuts and remove the brake booster.
Remove the gasket from the brake booster.
| 19. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY |
![]() |
Remove the vacuum check valve from the brake booster.
Remove the grommet from the brake booster.