Home › BRAKE › BRAKE › BRAKE BOOSTER (for Sedan LHD)

BRAKE BOOSTER (for Sedan LHD) > REMOVAL

for Preparation Click here


NOTICE:
Release the vacuum from booster by depressing the brake pedal several times.
Then remove the brake master cylinder from brake booster.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.



3. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



9. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



10. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal.



11. REMOVE COWL TOP PANEL OUTER


A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



12. REMOVE INSTRUMENT PANEL UNDER TRAY


B132341
  1. Disengage the 4 claws and open the instrument panel under tray.



    B132333
  1. Remove the 2 <A> screws.

  1. Disengage the 6 claws and remove the instrument panel under tray.



13. REMOVE BATTERY


14. REMOVE BATTERY TRAY


15. REMOVE BATTERY CARRIER


16. REMOVE BRAKE ACTUATOR (w/ ABS)


C241444
  1. Release the lock lever and disconnect the brake actuator connector.



    C243345
  1. Using a union nut wrench 10 mm, separate the brake tube from the front flexible hose.



    C243346
  1. Using a union nut wrench 10 mm, separate the 2 brake tubes from the brake tube No. 1 way.



    C243347
  1. Using a union nut wrench 10 mm, separate the 2 brake tubes from the brake master cylinder.



    C241445
  1. Using a union nut wrench 10 mm, separate the 6 brake tubes from the brake actuator.



    C241446E01
  1. Use tags or labels to identify the place to reconnect each brake tube.
    Text in Illustration 
    *a
    To Front Wheel RH
    *b
    To Front Wheel LH
    *c
    To Rear Wheel RH
    *d
    To Rear Wheel LH
    *e
    From 1st Master Cylinder
    *f
    From 2nd Master Cylinder



    C116918
  1. Disconnect the brake tube clamp.



    C168356
  1. Remove the 3 bolts and the actuator with bracket.



17. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)


C116933
  1. Slide the clip and disconnect the reservoir tube.



18. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY
  1. Disconnect the brake fluid level warning switch connector.



  1. w/o ABS:



      C121832E01
    1. Using SST, separate the 3 brake tubes from the brake tube way.

      SST
      09023-00100  



    C121690E01
  1. Using SST, separate the 2 brake tubes from the brake master cylinder sub-assembly.

    SST
    09023-00100  



    C116934
  1. w/ ABS:

    1. Remove the 2 nuts and remove the brake master cylinder sub-assembly.



    C121833
  1. w/o ABS:

    1. Remove the 2 nuts and brake tube way and remove the brake master cylinder sub-assembly.

  1. Remove the O-ring from the brake master cylinder sub-assembly.

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. Release the vacuum from booster by depressing the brake pedal several times. Then remove the brake master cylinder from brake booster.
    4. When installing the brake master cylinder sub-assembly onto the brake booster, or when removing the brake master cylinder sub-assembly from the brake booster, make sure that the brake master cylinder sub-assembly is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling off.
    5. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the piston.
    6. Do not use any other type of grease or fluid.



19. SEPARATE BRAKE MASTER CYLINDER PUSH ROD CLEVIS


C116880
  1. Remove the brake pedal return spring.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.



20. REMOVE BRAKE BOOSTER


    C116915E01
  1. w/o ABS:

    1. Using SST, separate the 2 brake tubes from the brake tube No. 1 way.

      SST
      09023-00100  



    2. C121837
    3. Using SST, remove the brake tube assembly from the proportioning valve.

      SST
      09023-00100  



    C116936
  1. Slide the clip and disconnect the vacuum hose from the check valve.



    C116943
  1. Remove the 4 nuts and remove the brake booster.

  1. Remove the gasket from the brake booster.

  1. Loosen the push rod lock nut and remove the push rod clevis.



21. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY


C116937
  1. Remove the vacuum check valve from the brake booster.

  1. Remove the grommet from the brake booster.