Home › BODY ELECTRICAL › OTHER SYSTEM › POWER OUTLET SOCKET (for Hatchback)

POWER OUTLET SOCKET (for Hatchback) > REMOVAL



1. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



    E107742E01
  1. Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



2. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



    E107744E01
  1. Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



3. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.



    B132364
  1. Disengage the 2 claws and 5 clips.



    B132365E01
  1. After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.



4. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (w/ Cassette Tape Player)


B132368E02
  1. Disengage the 2 claws and 4 clips and remove the instrument cluster finish panel center.

    NOTICE:
    1. Grip the rib portion of the instrument cluster finish panel center by hand to remove it.
    2. To avoid breakage of the instrument cluster finish panel center when removing it, do not apply excessive force to the register or pull out the link or panel portions.



5. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY LOWER CENTER


I101155
  1. Disengage the 3 clips and 2 claws and remove the air conditioning panel.



    I101156
  1. Disconnect the 3 connectors and clamp.



6. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I101157
  1. Disconnect the air mix control cable from the clamp.

  1. Disengage the 2 claws and disconnect the air mix damper control cable.



7. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I101158
  1. Disengage the 2 claws and disconnect the defroster damper control cable.



8. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I101159
  1. Disengage the 2 claws and disconnect the air inlet damper control cable.



9. REMOVE POWER OUTLET SOCKET


    B117776
  1. Disconnect the power outlet connector.



    B117777
  1. Using a screwdriver, disengage the claw, then turn the power outlet socket counterclockwise and push the power outlet socket half way out.



    B117778
  1. Align the protrusion of the power outlet socket with the cutout of the power outlet socket cover and then push the power outlet socket out.



10. REMOVE POWER OUTLET SOCKET COVER


    B117779
  1. Disengage the 2 claws and remove the power outlet socket cover.