Home › BRAKE › BRAKE › PROPORTIONING VALVE (for Sedan)

PROPORTIONING VALVE (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL PROPORTIONING VALVE


C121842
  1. Install the proportioning valve onto the proportioning valve bracket with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C121841E01
  1. Install the 2 bolts onto the proportioning valve bracket in the sequence order shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



    C121840
  1. Using SST, install the 5 brake tubes onto the proportioning valve.

    SST
    09023-00100  

    Torque:
    for use without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    for use with SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    2. This torque value is effective when SST is parallel to a torque wrench.



2. FILL RESERVOIR WITH BRAKE FLUID


C133125E02
  1. Remove the cowl top No. 2 ventilator louver center.



    C133126E01
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



3. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C116910E02
  1. Using a union nut wrench (10 mm), disconnect the brake tubes from the master cylinder.



    C116911E01
  1. Slowly depress the brake pedal and hold it there (Step A).



    C116912E01
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat steps A and B 3 or 4 times.



    C116910E02
  1. Using a union nut wrench (10 mm), connect the brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat steps C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf } for Front Brake
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for Rear Brake

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



5. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3
    SAE J1704 or FMVSS No. 116 DOT4



6. CHECK FOR BRAKE FLUID LEAKAGE