Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU

E114510E06


B108641E08

  1. Disconnect the 4B and 4E main body ECU (vehicle rear side) connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    BECU (4B-30) - GND1 (4E-17)
    L - W-B
    Battery (power supply)
    Always
    10 to 14 V
    GND1 (4E-17) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU (vehicle rear side) connectors.

  4. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    KSW (4D-7) - GND1 (4E-17)
    Y - W-B
    Key unlock warning switch input
    Key inserted
    0 V
    KSW (4D-7) - GND1 (4E-17)
    Y - W-B
    Key unlock warning switch input
    No key in ignition key cylinder
    10 to 14 V
    DCTY (4A-21) - Body ground
    R - Body ground
    Driver side door courtesy switch input
    Driver side door closed
    10 to 14 V
    DCTY (4A-21) - Body ground
    R - Body ground
    Driver side door courtesy switch input
    Driver side door open
    0 V
    PCTY (4A-24) - Body ground
    L - Body ground
    Passenger side door courtesy switch input
    Passenger side door closed
    10 to 14 V
    PCTY (4A-24) - Body ground
    L - Body ground
    Passenger side door courtesy switch input
    Passenger side door open
    0 V
    RRCY (4A-20) - Body ground
    L - Body ground
    Rear RH door courtesy switch input
    Rear RH door closed
    10 to 14 V
    RRCY (4A-20) - Body ground
    L - Body ground
    Rear RH door courtesy switch input
    Rear RH door open
    0 V
    RRCY (4A-5) - Body ground
    G - Body ground
    Rear LH door courtesy switch input
    Rear LH door closed
    10 to 14 V
    RRCY (4A-5) - Body ground
    G - Body ground
    Rear LH door courtesy switch input
    Rear LH door open
    0 V
    BCTY (4A-7) - Body ground
    SB- Body ground
    Back door courtesy switch input
    Back side door closed
    10 to 14 V
    BCTY (4A-7) - Body ground
    SB- Body ground
    Back door courtesy switch input
    Back side door open
    0 V
    PRG (D33-17) - Body ground
    W - Body ground
    Door control receiver output
    Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
    6 to 7 V → Below 1 V → 6 to 7 V
    RDA (D33-16) - Body ground
    R - Body ground
    Door control receiver input
    Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
    Below 1 V → 6 to 7 V → Below 1 V
    HAZ (4S-17) - Body ground
    B - Body ground
    Hazard warning light signal
    Answer-back ON
    Pulse generation
    HAZ (4S-17) - Body ground
    B - Body ground
    Hazard warning light signal
    Answer-back OFF
    10 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.


CHECK DOOR CONTROL RECEIVER

B123878

  1. Disconnect the door control receiver connector.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    +B (J13-5) - GND (J13-1)
    L - W-B
    Battery (power supply)
    Always
    10 to 14 V
    GND (J13-1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the door control receiver connector.

  4. Measure the voltage of the wire harness side connectors.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PRG (J13-3) - Body ground
    W - Body ground
    Door control receiver output
    Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
    6 to 7 V → Below 1 V → 6 to 7 V
    RDA (J13-2) - Body ground
    R - Body ground
    Door control receiver input
    Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
    Below 1 V → 6 to 7 V → Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.