Home › ENGINE · 1NZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0133    Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 1)

for Preparation Click here

HINT:
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DESCRIPTION

Refer to DTC P0130 .

DTC No.
DTC Detection Conditions
Trouble Areas
P0133
While idling with warm engine, response time for voltage output of Heated Oxygen (HO2) sensor to change from rich to lean or from lean to rich is 1 second or more (2 trip detection logic)
  1. Open or short in HO2 sensor (sensor 1) circuit
  2. HO2 sensor (sensor 1)
  3. HO2 sensor heater (sensor 1)
  4. Integration relay (EFI relay)
  5. Air induction system
  6. Fuel pressure
  7. Injector
  8. ECM

WIRING DIAGRAM

Refer to DTC P0130 .

CONFIRMATION DRIVING PATTERN


A128471E02

HINT:
This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.

  1. (1) Connect an intelligent tester to the DLC3.
  2. (2) Turn the ignition switch to ON and turn the tester on.
  3. (3) Clear DTCs (Click here).
  4. (4) Switch the ECM from normal mode to check mode (Click here).
  5. (5) Start the engine.
  6. (6) Allow the engine to idle until the engine coolant temperature reaches 40°C (104°F).
  7. (7) Drive the vehicle at a vehicle speed of more than 40 km/h (25 mph) for 35 seconds or more.
  8. (8) Allow the engine to idle for 40 seconds or more.
  9. (9) Repeat steps (7) and (8) described above at least 3 times.
  10. (10) Allow the engine to idle for 40 seconds or more.

HINT:
The MIL is illuminated during step (10) if a malfunction still exists.

NOTICE:
If the conditions in this test are not strictly followed, malfunctions may not be detected.


INSPECTION PROCEDURE

HINT:
It is possible that the malfunctioning area can be found using the Active Test Control operation. The Active Test can determine if the heated oxygen sensor or other potential trouble areas are malfunctioning or not.
The injection volume can be switched to -12.5% (decrease) or +25% (increase) by the Active Test.
The Active Test procedure enables a technician to check and graph the voltage outputs of the heated oxygen sensors.

  1. Procedure:
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch to ON.
    3. Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
    4. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Active Test while the engine is idling.

Standard:
The heated oxygen sensor reacts in accordance with the increases and decreases in injection volume:
+25% → RICH output: More than 0.5 V
-12.5% → LEAN output: Less than 0.4 V

NOTICE:
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of 20 seconds.
If the vehicle is short of fuel, the air-fuel ratio becomes LEAN and the DTCs are recorded.


Case
Heated Oxygen Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A150789E04
A150787E01
A150788E03
-
2
A150787E01
A150790E01
A150787E01
A150788E03
  1. Heated oxygen sensor (Sensor 1)
  2. Heated oxygen sensor heater (Sensor 1)
  3. Heated oxygen sensor circuit (Sensor 1)
3
A150787E01
A150789E04
A150787E01
A150790E01
  1. Heated oxygen sensor (Sensor 2)
  2. Heated oxygen sensor heater (Sensor 2)
  3. Heated oxygen sensor circuit (Sensor 2)
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leak from exhaust system (Air-fuel ratio extremely RICH or LEAN)

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0133)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0133
    A
    P0133 and other DTCs
    B

    HINT:
    If any DTCs other than P0133 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (HEATED OXYGEN SENSOR DURING IDLING)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1S1.

  1. Warm up the Heated Oxygen (HO2) sensor at an engine speed of 2,500 rpm for approximately 90 seconds.

  1. Read the voltage output of the front HO2 sensor displayed on the tester, while the engine is idling.

    Standard:
    Fluctuates between less than 0.4 V and more than 0.5 V, and period "t" is less than 1 second (refer to table below).


A128469E03



OK
Go to step 9
NG


3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A107936E07
  1. Disconnect the C36 HO2 sensor (sensor 1) connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    HT1A (1) - +B (2)
    5.3 to 7.5 Ω at 20 °C (68°F)
    HT1A (1) - E2 (4)
    10 kΩ or higher

  1. Reconnect the HO2 sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR
OK


4.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY)
A107921E21
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI fuse.

    1. Remove the EFI fuse from the integration relay.

    2. Check the EFI fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI fuse.

  1. Inspect the EFI relay.

    1. Check the EFI relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION NO.1 RELAY
OK


5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
A105980E01

A112568E03

  1. Disconnect the C36 HO2 sensor (sensor 1) connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    OX1A (C36-3) - OX1A (C20-112)
    Below 1 Ω
    HT1A (C36-1) - HT1A (C20-109)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    OX1A (C36-3) or OX1A (C20-112) - Body ground
    10 kΩ or higher
    HT1A (C36-1) or HT1A (C20-109) - Body ground

  1. Reconnect the HO2 sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.INSPECT FUEL INJECTOR
  1. Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).



NG
REPLACE FUEL INJECTOR (Click here)
OK

REPLACE HEATED OXYGEN SENSOR (Click here)  

9.PERFORM CONFIRMATION DRIVING PATTERN

HINT:
Clear all DTCs before performing the confirmation driving pattern.


NEXT


10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed To
    P0133
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HEATED OXYGEN SENSOR (Click here)