Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Hazard Warning Switch Circuit

for Preparation Click here


DESCRIPTION

LHD models: When the hazard warning signal switch is turned on, the turn signal flasher relay in the main body ECU turns on to flash the hazard warning signal lights.
RHD models: When the hazard warning signal switch is turned on, the turn signal flasher relay turns on to flash the hazard warning signal lights.

WIRING DIAGRAM


B129623E03


B129624E01


INSPECTION PROCEDURE

1.CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result:
    Vehicle Type
    Proceed to
    LHD models
    A
    RHD models
    B



B
Go to step 8
A


2.INSPECT FUSE (GAUGE, HAZ)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Remove the HAZ fuse from the engine room relay block.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the GAUGE and HAZ fuses.



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (FUSE - MAIN BODY ECU)


    B135312E01
  1. Disconnect the 4B main body ECU connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    4B-32 - Body ground
    Always
    10 to 14 V

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT HAZARD WARNING SIGNAL SWITCH


  1. Hatchback:



      E107908E06
    1. Remove the hazard warning signal switch.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 4
      OFF
      10 kΩ or higher
      1 - 4
      ON
      Below 1 Ω

    3. Reinstall the hazard warning signal switch.



  1. Sedan:



      B141750E01
    1. Remove the hazard warning signal switch.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      15 - 4
      OFF
      10 kΩ or higher
      15 - 4
      ON
      Below 1 Ω

    3. Reinstall the hazard warning signal switch.



NG
REPLACE HAZARD WARNING SIGNAL SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH - MAIN BODY ECU)


  1. Hatchback:



      B135317E01
    1. Disconnect the D7 hazard warning signal switch connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D7-4 - 4S-17 (EHW)
      Below 1 Ω
      D7-4 or 4S-17 (EHW) - Body ground
      10 kΩ or higher

    4. Reconnect the hazard warning signal switch connector.

    5. Reconnect the main body ECU connector.



  1. Sedan:



      B141751E01
    1. Disconnect the D85 hazard warning signal switch connector.

    2. Disconnect the 4S main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D85-15 - 4S-17 (EHW)
      Below 1 Ω
      D85-15 or 4S-17 (EHW) - Body ground
      10 kΩ or higher

    4. Reconnect the hazard warning signal switch connector.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH - BODY GROUND)


  1. Hatchback:



      B129622E03
    1. Disconnect the D7 hazard warning signal switch connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D7-1 - Body ground
      Below 1 Ω

    3. Reconnect the hazard warning signal switch connector.



  1. Sedan:



      B141752E01
    1. Disconnect the D85 hazard warning signal switch connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D85-4 - Body ground
      Below 1 Ω

    3. Reconnect the hazard warning signal switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)


    B135314E01
  1. Disconnect the 4E main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4E-17 (GND)- Body ground
    Below 1 Ω

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.INSPECT FUSE (GAUGE, HAZ)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Remove the HAZ fuse from the engine room relay block.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the GAUGE and HAZ fuses.



NG
REPLACE FUSE (GAUGE, HAZ)
OK


9.INSPECT TURN SIGNAL FLASHER RELAY


    E101506E02
  1. Measure the voltage

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D71-2 (LR) - Body ground
    Hazard warning signal switch OFF → ON
    0 V → 10 to 14 V (60 to 120 times per minute)
    D71-3 (LL) - Body ground
    Hazard warning signal switch OFF → ON
    0 V → 10 to 14 V (60 to 120 times per minute)
    D71-8 (HAZ) - Body ground
    Hazard warning signal switch OFF → ON
    10 to 14 V → 0 V



NG
REPLACE TURN SIGNAL FLASHER RELAY
OK


10.INSPECT HAZARD WARNING SIGNAL SWITCH


  1. Hatchback:



      E107908E06
    1. Remove the hazard warning signal switch.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 4
      OFF
      10 kΩ or higher
      1 - 4
      ON
      Below 1 Ω

    3. Reinstall the hazard warning signal switch.



  1. Sedan:



      B141750E01
    1. Remove the hazard warning signal switch.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      15 - 4
      OFF
      10 kΩ or higher
      15 - 4
      ON
      Below 1 Ω

    3. Reinstall the hazard warning signal switch.



NG
REPLACE HAZARD WARNING SIGNAL SWITCH
OK


11.CHECK HARNESS AND CONNECTOR (FUSE - TURN SIGNAL FLASHER RELAY)


    E120966E02
  1. Disconnect the D71 turn signal flasher connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D71-1 (IG) - Body ground
    Ignition switch ON
    10 to 14 V
    D71-4 (B) - Body ground
    Always
    10 to 14 V

  1. Reconnect the turn signal flasher connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER RELAY - HAZARD WARNING SIGNAL SWITCH)


  1. Hatchback:



      B128875E02
    1. Disconnect the D7 hazard warning signal switch connector.

    2. Disconnect the D71 turn signal flasher relay connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D7-4 - D71-8 (HAZ)
      Below 1 Ω
      D7-4 or D71-8 (HAZ) - Body ground
      10 kΩ or higher

    4. Reconnect the hazard warning signal switch connector.

    5. Reconnect the turn signal flasher relay connector.



  1. Sedan:



      B141753E01
    1. Disconnect the D85 hazard warning signal switch connector.

    2. Disconnect the D71 turn signal flasher relay connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D85-15 - D71-8 (HAZ)
      Below 1 Ω
      D85-15 or D71-8 (HAZ) - Body ground
      10 kΩ or higher

    4. Reconnect the hazard warning signal switch connector.

    5. Reconnect the turn signal flasher relay connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH - BODY GROUND)


  1. Hatchback:



      B129622E03
    1. Disconnect the D7 hazard warning signal switch connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D7-1 - Body ground
      Below 1 Ω

    3. Reconnect the hazard warning signal switch connector.



  1. Sedan:



      B141752E01
    1. Disconnect the D85 hazard warning signal switch connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      D85-4 - Body ground
      Below 1 Ω

    3. Reconnect the hazard warning signal switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (TURN SIGNAL FLASHER RELAY - BODY GROUND)