Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Back-up Light Circuit

for Preparation Click here


DESCRIPTION

A/T models: The park/neutral position switch turns on when the shift lever is moved into the R position, causing the back-up light to illuminate.
M/T models: The back-up light switch turns on when the shift lever is moved into the R position, causing the back-up light to illuminate.

WIRING DIAGRAM


E120013E09


INSPECTION PROCEDURE

1.INSPECT FUSE (GAUGE)
  1. Remove the GAUGE fuse from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the GAUGE fuse.



NG
REPLACE FUSE
OK


2.INSPECT BULB (BACK-UP LIGHT BULB)


  1. Hatchback:



      B129860E02
    1. Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the back-up light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 6
      Back-up light illuminates

    3. Reinstall the rear combination light assembly.



  1. Sedan:



      B141033E01
    1. Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the back-up light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 5
      Negative battery - Terminal 6
      Back-up light illuminates

    3. Reinstall the rear combination light assembly.



NG
REPLACE BULB
OK


3.CHECK VEHICLE TYPE
  1. Check transaxle type.

Result:
Transaxle Type
Proceed to
A/T
A
M/T
B



B
Go to step 7
A


4.INSPECT PARK / NEUTRAL POSITION SWITCH


    C110340E19
  1. Disconnect the C27 park / neutral position switch connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Condition
    Shift Position
    Specified Condition
    2 (RB) - 1 (RL)
    R
    Below 1 Ω
    2 (RB) - 1 (RL)
    Except R
    10 kΩ or higher

  1. Reconnect the park / neutral position switch connector.



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


5.CHECK HARNESS AND CONNECTOR (GAUGE FUSE - PARK/NEUTRAL POSITION SWITCH)


    B124048E02
  1. Disconnect the C27 park / neutral position switch connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Condition
    Condition
    Specified Condition
    C27-2 (RB) - Body ground
    Ignition switch ON
    10 to 14 V

  1. Disconnect the C27 park / neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - REAR COMBINATION LIGHT)


  1. Hatchback:



      B125723E05
    1. Disconnect the C27 park/neutral position switch connector.

    2. Disconnect the J3 or J4 rear combination light assembly connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Condition
      Specified Condition
      C27-1 (RL) - J3-1
      Below 1 Ω
      C27-1 (RL) - J4-1
      Below 1 Ω
      C27-1 (RL) or J3-1 - Body ground
      10 kΩ or higher
      C27-1 (RL) or J4-1 - Body ground
      10 kΩ or higher

    4. Reconnect the park / neutral position switch connector.

    5. Reconnect the rear combination light assembly connector.



  1. Sedan:



      E131560E01
    1. Disconnect the C27 park/neutral position switch connector.

    2. Disconnect the J41 or J42 rear combination light assembly connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Condition
      Specified Condition
      C27-1 (RL) - J41-5
      Below 1 Ω
      C27-1 (RL) - J42-5
      Below 1 Ω
      C27-1 (RL) or J41-5 - Body ground
      10 kΩ or higher
      C27-1 (RL) or J42-5 - Body ground
      10 kΩ or higher

    4. Reconnect the park / neutral position switch connector.

    5. Reconnect the rear combination light assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND) 

7.INSPECT BACK-UP LIGHT SWITCH


    B133141E02
  1. Disconnect the C22 back-up light switch connector.

  1. Measure the resistance.

    Standard resistance:
    Shift Position
    Tester Condition
    Specified Condition
    R
    2 - 1
    Below 1 Ω
    Except R
    2 - 1
    10 kΩ or higher

  1. Reconnect the back-up light switch connector.



NG
REPLACE BACK-UP LIGHT SWITCH
OK


8.CHECK HARNESS AND CONNECTOR (GAUGE FUSE - BACK-UP LIGHT SWITCH)


    B146575E01
  1. Disconnect the C22 back-up light switch connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Condition
    Condition
    Specified Condition
    C22-2 - Body ground
    Ignition switch ON
    10 to 14 V

  1. Reconnect the back-up light switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH - REAR COMBINATION LIGHT ASSEMBLY)


  1. Hatchback:



      B125724E05
    1. Disconnect the C22 back-up light switch connector.

    2. Disconnect the J3 or J4 rear combination light assembly connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Condition
      Specified Condition
      C22-1 - J3-1
      Below 1 Ω
      C22-1 - J4-1
      Below 1 Ω
      C22-1 or J3-1 - Body ground
      10 kΩ or higher
      C22-1 or J4-1 - Body ground
      10 kΩ or higher

    4. Reconnect the back-up light switch connector.

    5. Reconnect the rear combination light assembly connectors.



  1. Sedan:



      E131561E01
    1. Disconnect the C22 back-up light switch connector.

    2. Disconnect the J41 or J42 rear combination light assembly connectors.

    3. Measure the resistance.

      Standard resistance:
      Tester Condition
      Specified Condition
      C22-1 - J41-5
      Below 1 Ω
      C22-1 - J42-5
      Below 1 Ω
      C22-1 or J41-5 - Body ground
      10 kΩ or higher
      C22-1 or J42-5 - Body ground
      10 kΩ or higher

    4. Reconnect the back-up light switch connector.

    5. Reconnect the rear combination light assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - BODY GROUND)