Home › BODY ELECTRICAL › METER › METER / GAUGE SYSTEM (for Sedan)

METER / GAUGE SYSTEM (for Sedan) > Warning Buzzer does not Sound

for Preparation Click here


DESCRIPTION

The combination meter assembly controls the buzzers in accordance with signals from the front seat inner belt assembly, the main body ECU and the TL-P relay.

WIRING DIAGRAM


E126922E01


INSPECTION PROCEDURE

1.CHECK BUZZER (SEAT BELT, KEY REMINDER, TAIL LIGHT REMINDER)
  1. Check that the seat belt warning, key reminder and taillight reminder warning buzzers sound.

    Result:

    Result
    Proceed to
    Seat belt warning buzzer does not sound
    (where equipped with seat belt warning system)
    A
    Key reminder warning buzzer does not sound
    (where equipped with key reminder warning system)
    B
    Taillight reminder warning buzzer does not sound
    (Meter illuminations normal)
    C
    No warning buzzers sound
    D

    HINT:
    1. Seat belt warning buzzer on: Ignition switch ON, seat belt is unfastened, and vehicle speed is 20km/h (12.4mph) or more.
    2. Key reminder warning buzzer on: Ignition switch is OFF, key is in ignition key cylinder, and driver side door is open.
    3. Taillight reminder warning buzzer on: Ignition switch is OFF, key is not in ignition key cylinder, and driver side door is open.



B
GO TO KEY REMINDER WARNING SYSTEM

C
Go to step 10

D
REPLACE COMBINATION METER ASSEMBLY
A


2.CHECK SEAT BELT WARNING BUZZER
  1. Check which seat belt warning buzzer (driver or front passenger) does not sound.

    Result:
    Result
    Proceed to
    Driver side
    A
    Passenger side
    B



B
Go to step 6
A


3.READ VALUE USING INTELLIGENT TESTER (D-SEAT BUCKLE SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester on.

  1. Read the Data List according to the prompts displayed on the tester

    Main Body:

    Item
    Measurement Item/Range (Display)
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Buckle switch (Driver side) /
    UNSET: Driver seat belt is not fastened
    SET: Driver seat belt is fastened
    NG: Data is not determined
    UNSET / SET
    -



OK
REPLACE COMBINATION METER ASSEMBLY
NG


4.CHECK FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)


    B209386E02
  1. Disconnect the J35 or J54 front seat inner belt assembly (driver side) connector.

  1. Measure the resistance.

    Standard resistance:
    Tester connection
    Condition
    Specified Condition
    1 (E) - 2 (+)
    Tongue plate fastened
    Below 1Ω
    1 (E) - 2 (+)
    Tongue plate released
    10 kΩ or higher

  1. Reconnect the front seat inner belt assembly (driver side) connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - MAIN BODY ECU)


    B209387E02
  1. Disconnect the J35 or J54 front seat inner belt assembly (driver side) connector.

  1. Disconnect the D33 main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D33-9 (DBKL) - J35-2 (+)*1
    Below 1Ω
    D33-9 (DBKL) or J35-2 (+)*1 - Body ground
    10 kΩ or higher
    D33-9 (DBKL) - J54-2 (+)*2
    Below 1Ω
    D33-9 (DBKL) or J54-2 (+)*2 - Body ground
    10 kΩ or higher

    1. *1: LHD
    2. *2: RHD

  1. Reconnect the front seat inner belt assembly (driver side) connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.READ VALUE USING INTELLIGENT TESTER (P-SEAT BELT BUCKLE SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester on.

  1. Read the Data List according to the prompts displayed on the tester.

    Combination Meter:

    Item
    Measurement Item/Range (Display)
    Normal Condition
    Diagnostic Note
    P-Seatbelt Buckle SW
    Buckle switch (Passenger side) /
    UNSET: Front passenger seat belt is not fastened
    SET: Front passenger seat belt is fastened
    UNSET / SET
    -



OK
REPLACE COMBINATION METER ASSEMBLY
NG


7.CHECK FRONT SEAT INNER BELT ASSEMBLY (PASSENGER SIDE)


    B120593E03
  1. Disconnect the J34 or J35 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the occupant detection sensor connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (E) - Occupant detection sensor connector-1
    Tongue plate fastened
    10 kΩ or higher
    1 (E) - Occupant detection sensor connector-1
    Tongue plate unfastened
    Below 1Ω
    1 (E) - Body ground
    Always
    10 kΩ or higher
    Occupant detection sensor connector-1 - Body ground
    Always
    10 kΩ or higher
    2 (+) - Occupant detection sensor connector-3
    Always
    Below 1Ω
    2 (+) or Occupant detection sensor connector-3 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the front seat inner belt assembly (passenger side) connector.

  1. Reconnect the occupant detection sensor connector.



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY
OK


8.CHECK OCCUPANT DETECTION SENSOR


    B120626E03
  1. Disconnect the occupant detection sensor connector.

  1. Measure the resistance.

    Measure the resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Front passenger seat unoccupied
    10 kΩ or higher
    1 - 3
    Front passenger seat occupied
    Below 1Ω

  1. Reconnect the occupant detection sensor connector.



NG
REPLACE OCCUPANT DETECTION SENSOR
OK


9.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)


    E126926E03
  1. Disconnect the J34 or J35 front seat inner belt assembly (passenger side) connector.

  1. Disconnect the D1 combination meter assembly connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J34-2 (+)*1 - D1-10 (P/SB)
    Below 1Ω
    J35-2 (+)*2 - D1-10 (P/SB)
    Below 1Ω

    1. *1: LHD
    2. *2: RHD

  1. Reconnect the front seat inner belt assembly (passenger side) connector.

  1. Reconnect the combination meter assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY 

10.READ VALUE USING INTELLIGENT TESTER (D DOOR COURTESY SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester on.

  1. Read the Data List according to the prompts displayed on the tester.

    Main Body:

    Item
    Measurement Item/Range (Display)
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Front door courtesy switch (Driver side) ON / OFF
    ON: Front door open
    OFF: Front door closed
    -



OK
Go to step 13
NG


11.INSPECT FRONT DOOR COURTESY SWITCH (DRIVER SIDE)


    B129185E01
  1. Remove the front door courtesy switch (driver side).

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩ or higher

  1. Reinstall the front door courtesy switch (driver side).



NG
REPLACE FRONT DOOR COURTESY SWITCH
OK


12.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH - MAIN BODY ECU)


    B112021E30
  1. Disconnect the J2 or J1 front door courtesy switch connector.

  1. Disconnect the 4A main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    J2-1*1 - 4A-21 (DCTY)
    Below 1Ω
    J1-1*2 - 4A-21 (DCTY)
    Below 1Ω

    1. *1: LHD
    2. *2: RHD

  1. Reconnect the front door courtesy switch connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

13.INSPECT COMBINATION METER ASSEMBLY


    E126924E01
  1. Disconnect the D84 combination meter assembly connector.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D84-16 (IND) - Body ground
    Headlight dimmer switch tail or head position
    10 to 14 V

  1. Reconnect the combination meter assembly connector.



OK
REPLACE COMBINATION METER ASSEMBLY
NG


14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - MAIN BODY ECU)


    E126925E01
  1. Disconnect the D84 combination meter assembly connector.

  1. Disconnect the 4Q main body ECU connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    D84-16 (IND) - 4Q-2
    Below 1 Ω

  1. Reconnect the combination meter assembly connector.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO LIGHTING SYSTEM