Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Taillight Circuit

for Preparation Click here


DESCRIPTION

When the light control switch, located on the headlight dimmer switch, is turned to the TAIL position, the front position lights, rear taillights and license plate light illuminate.

WIRING DIAGRAM


E173970E01


INSPECTION PROCEDURE

1.CHECK WHETHER LIGHTS ILLUMINATE
  1. Check whether the following lights illuminate: Front position lights, Rear taillights and License plate light.

    Result:

    Illumination Condition
    Proceed To
    All lights illuminate
    A
    No lights illuminate
    B
    Front position lights do not illuminate
    C
    Rear taillights do not illuminate
    D
    License plate light does not illuminate
    E



B
Go to step 2

C
Go to step 6

D
Go to step 8

E
Go to step 10
A

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT FUSE (TAIL)
  1. Remove the TAIL fuse from the main body ECU.

  1. Measure the resistance.

    Standard resistance:
    Below 1 Ω

  1. Reconnect the TAIL fuse.



NG
REPLACE FUSE
OK


3.INSPECT HEADLIGHT DIMMER SWITCH


    B126089E17
  1. Remove the headlight dimmer switch.

  1. Inspect the light control switch.

  1. Measure the resistance.

    Standard resistance:
    LHD:
    Tester Connection
    Condition
    Specified Condition
    10 (T1) - 13 (B1)
    TAIL
    Below 1 Ω
    10 (T1) - 13 (B1)
    OFF
    10 kΩ or higher
    10 (T1) - 13 (B1)
    HEAD
    Below 1 Ω
    10 (T1) - 13 (B1)
    OFF
    10 kΩ or higher
    11 (ED) - 12 (RF)
    HEAD
    Below 1 Ω
    11 (ED) - 12 (RF)
    OFF
    10 kΩ or higher
    RHD:
    Tester Connection
    Condition
    Specified Condition
    5 (B1) - 8 (T1)
    TAIL
    Below 1 Ω
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher
    5 (B1) - 8 (T1)
    HEAD
    Below 1 Ω
    5 (B1) - 8 (T1)
    OFF
    10 kΩ or higher
    6 (RF) - 7 (ED)
    HEAD
    Below 1 Ω
    6 (RF) - 7 (ED)
    OFF
    10 kΩ or higher

  1. Reinstall the headlight dimmer switch.



NG
REPLACE HEADLIGHT DIMMER SWITCH
OK


4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH)


    B126090E14
  1. Disconnect the D4 headlight dimmer switch.

  1. Measure the voltage.

    Standard voltage:
    LHD:
    Tester Connection
    Specified Condition
    D4-13 (B1) - Body Ground
    10 to 14 V
    RHD:
    Tester Connection
    Specified Condition
    D4-5 (B1) - Body Ground
    10 to 14 V

  1. Reconnect the headlight dimmer switch.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT MAIN BODY ECU
E146383E01
  1. Disconnect the 4A, 4B and 4E main body ECU connectors.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    4A-10 - 4E-10
    Below 1 Ω
    4A-29 - 4E10
    Below 1 Ω
    4B-33 - 4E-10
    Below 1 Ω

  1. Reconnect the main body ECU connectors.



NG
REPLACE MAIN BODY ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER SWITCH - MAIN BODY ECU) 

6.INSPECT BULB (FRONT POSITION LIGHT BULB)


  1. Hatchback:



      B141827E01
    1. Remove the front position light.

    2. Apply battery voltage to the terminals and check that the front position light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 1
      Negative battery - Terminal 2
      Front position light illuminates

    3. Reinstall the front position light.



  1. Sedan:



      B144226E05
    1. Remove the front position light.

    2. Apply battery voltage to the terminals and check that the front position light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 3
      Negative battery - Terminal 2
      Front position light illuminates

    3. Reinstall the front position light.



NG
REPLACE BULB
OK


7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POSITION LIGHT)


  1. Hatchback:



      B135318E02
    1. Disconnect the B3 and B7 front position light connectors.

    2. Disconnect the 4B main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4B-33 - B3-1
      Below 1 Ω
      4B-33 - B7-1
      Below 1 Ω
      4B-33 or B3-1 - Body ground
      10 kΩ or higher
      4B-33 or B7-1 - Body ground
      10 kΩ or higher

    4. Reconnect the front position light connectors.

    5. Reconnect the main body ECU connector.



  1. Sedan:



      B144227E05
    1. Disconnect the B16 and B17 front position light connectors.

    2. Disconnect the 4B main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4B-33 - B16-3
      Below 1 Ω
      4B-33 - B17-3
      Below 1 Ω
      4B-33 or B16-3 - Body ground
      10 kΩ or higher
      4B-33 or B17-3 - Body ground
      10 kΩ or higher

    4. Reconnect the front position light connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT POSITION LIGHT - BODY GROUND) 

8.INSPECT BULB (REAR TAILLIGHT BULB)


  1. Hatchback:



      B129860E03
    1. Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear taillight illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 4
      Negative battery - Terminal 6
      Rear taillight illuminates

    3. Reinstall the rear combination light assembly.



  1. Sedan:



      B141033E01
    1. Remove the rear combination light assembly.

    2. Apply battery voltage to the terminals and check that the rear taillight illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 4
      Negative battery - Terminal 6
      Rear taillight illuminates

    3. Reinstall the rear combination light assembly.



NG
REPLACE BULB
OK


9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR TAILLIGHT)


  1. Hatchback:



      B131873E05
    1. Disconnect the J3 and J4 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-10 - J3-4
      Below 1 Ω
      4A-29 - J4-4
      Below 1 Ω
      4A-10 or J3-4 - Body ground
      10 kΩ or higher
      4A-29 or J4-4 - Body ground
      10 kΩ or higher

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.



  1. Sedan:



      B141726E02
    1. Disconnect the J41 and J42 rear combination light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-10 - J41-4
      Below 1 Ω
      4A-29 - J42-4
      Below 1 Ω
      4A-10 or J41-4 - Body ground
      10 kΩ or higher
      4A-29 or J42-4 - Body ground
      10 kΩ or higher

    4. Reconnect the rear combination light assembly connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR TAILLIGHT - BODY GROUND) 

10.INSPECT BULB (LICENSE PLATE LIGHT BULB)


  1. Hatchback (G. C. C. Countries):



      B141830E03
    1. Remove the license plate light assembly.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light assembly.



  1. Hatchback (Except G. C. C. Countries):



      B141829E02
    1. Remove the license plate light assembly.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light assembly.



  1. Sedan:



      B141842E03
    1. Remove the license plate light assembly.

    2. Apply battery voltage to the terminals and check that the license plate light illuminates.

      Standard:
      Measurement Condition
      Standard
      Positive battery - Terminal 2
      Negative battery - Terminal 1
      License plate light illuminates

    3. Reinstall the license plate light assembly.



NG
REPLACE BULB
OK


11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - LICENSE PLATE LIGHT ASSEMBLY)


  1. Hatchback (G. C. C. Countries):



      B141839E01
    1. Disconnect the L1 license plate light assembly connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-29 - L1-2
      Below 1 Ω
      4A-29 or L1-2 - Body ground
      10 kΩ or higher

    4. Reconnect the license plate light assembly connector.

    5. Reconnect the main body ECU connector.



  1. Hatchback (Except G. C. C. Countries):



      B141840E01
    1. Disconnect the J38 license plate light assembly connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-29 - J38-2
      Below 1 Ω
      4A-29 or J38-2 - Body ground
      10 kΩ or higher

    4. Reconnect the license plate light assembly connector.

    5. Reconnect the main body ECU connector.



  1. Sedan:



      B141841E01
    1. Disconnect the J43 and J44 license plate light assembly connectors.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Specified Condition
      4A-29 - J43-2
      Below 1 Ω
      4A-29 - J44-2
      Below 1 Ω
      4A-29 or J43-2 - Body ground
      10 kΩ or higher
      4A-29 or J44-2 - Body ground
      10 kΩ or higher

    4. Reconnect the license plate light assembly connectors.

    5. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (LICENSE PLATE LIGHT ASSEMBLY - BODY GROUND)