U340E AUTOMATIC TRANSAXLE > SERVICE DATA |
| Automatic Transaxle System | ||
| Line pressure (Wheel locked) | ||
| Engine idling | D position | 372 to 412 kPa (3.8 to 4.2 kgf/cm2, 54 to 60 psi) |
| R position | 553 to 623 kPa (5.6 to 6.4 kgf/cm2, 80 to 90 psi) | |
| AT stall (Throttle valve fully opened) | D position | 1,126 to 1,226 kPa (11.5 to 12.5 kgf/cm2, 163 to 178 psi) |
| R position | 1,664 to 1,864 kPa (17.0 to 19.0 kgf/cm2, 241 to 270 psi) | |
| Engine stall revolution | D position | 2,150 to 2,550 rpm |
| Time lag | N → D position | Less than 1.2 seconds |
| N → R position | Less than 1.5 seconds | |
| Engine idle speed (A/C OFF) | N position | 650 to 750 rpm |
| Drive plate runout | Maximum | 0.20 mm (0.0079 in.) |
| Shift schedule (Tire size: 175/65R14) | ||
| D position | ||
| Throttle valve fully opened | 1 → 2 | 48 to 53 km/h (30 to 33 mph) |
| 2 → 3 | 91 to 99 km/h (57 to 62 mph) | |
| 3 → 4 | 142 to 151 km/h (88 to 94 mph) | |
| 4 → 3 | 137 to 145 km/h (85 to 90 mph) | |
| 3 → 2 | 86 to 93 km/h (53 to 58 mph) | |
| 2 → 1 | 40 to 44 km/h (25 to 27 mph) | |
| Throttle valve fully closed | 3 → 4 | 39 to 43 km/h (24 to 27 mph) |
| 4 → 3 | 29 to 33 km/h (18 to 21 mph) | |
| 2 position | ||
| Throttle valve fully opened | 1 → 2 | 48 to 53 km/h (30 to 33 mph) |
| 3 → 2 | 86 to 93 km/h (53 to 58 mph) | |
| 2 → 1 | 40 to 44 km/h (25 to 27 mph) | |
| L position | ||
| Throttle valve fully opened | 3 → 2 | 86 to 93 km/h (53 to 58 mph) |
| 2 → 1 | 43 to 47 km/h (27 to 30 mph) | |
| Lock-up point (Throttle valve opening 5 %) | ||
| D position | ||
| 4th gear | Lock-up ON | 53 to 57 km/h (33 to 35 mph) |
| Lock-up OFF | 50 to 54 km/h (31 to 34 mph) | |
| 3 position | ||
| 3rd gear | Lock-up ON | 91 to 99 km/h (57 to 62 mph) |
| Lock-up OFF | 86 to 93 km/h (53 to 58 mph) | |
| Shift schedule (Tire size: 185/60R15) | ||
| D position | ||
| Throttle valve fully opened | 1 → 2 | 49 to 55 km/h (30 to 34 mph) |
| 2 → 3 | 93 to 101 km/h (58 to 63 mph) | |
| 3 → 4 | 146 to 154 km/h (91 to 96 mph) | |
| 4 → 3 | 141 to 149 km/h (88 to 93 mph) | |
| 3 → 2 | 88 to 95 km/h (55 to 59 mph) | |
| 2 → 1 | 41 to 45 km/h (25 to 28 mph) | |
| Throttle valve fully closed | 3 → 4 | 40 to 44 km/h (25 to 27 mph) |
| 4 → 3 | 29 to 33 km/h (18 to 21 mph) | |
| 2 position | ||
| Throttle valve fully opened | 1 → 2 | 49 to 55 km/h (30 to 34 mph) |
| 3 → 2 | 88 to 95 km/h (55 to 59 mph) | |
| 2 → 1 | 41 to 45 km/h (25 to 28 mph) | |
| L position | ||
| Throttle valve fully opened | 3 → 2 | 88 to 95 km/h (55 to 59 mph) |
| 2 → 1 | 44 to 48 km/h (27 to 30 mph) | |
| Lock-up point (Throttle valve opening 5 %) | ||
| D position | ||
| 4th gear | Lock-up ON | 54 to 58 km/h (34 to 36 mph) |
| Lock-up OFF | 51 to 56 km/h (32 to 35 mph) | |
| 3 position | ||
| 3rd gear | Lock-up ON | 93 to 101 km/h (58 to 63 mph) |
| Lock-up OFF | 88 to 95 km/h (55 to 59 mph) | |
| Automatic Transaxle Unit | ||
| 2nd brake piston return spring free length | Standard | 15.85 mm (0.6240 in.) |
| 1st and reverse brake return spring free length | Standard | 21.71 mm (0.85472 in.) |
| Tapered roller bearing preload | New bearing Used bearing | 0.78 to 1.37 N*m (8.0 to 14.0 kgf*cm, 6.9 to 12.2 in.*lbf) 0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf) |
| Transaxle case side adjusting shim | Mark A Mark B Mark C Mark D Mark E Mark F Mark G Mark H Mark J Mark K Mark L Mark M Mark N Mark P Mark Q Mark R Mark S Mark T Mark U Mark V Mark W Mark X Mark Y | 1.80 mm (0.0709 in.) 1.85 mm (0.0728 in.) 1.90 mm (0.0748 in.) 1.95 mm (0.0768 in.) 2.00 mm (0.0787 in.) 2.05 mm (0.0807 in.) 2.08 mm (0.0819 in.) 2.11 mm (0.0831 in.) 2.14 mm (0.0843 in.) 2.17 mm (0.0854 in.) 2.20 mm (0.0866 in.) 2.23 mm (0.0878 in.) 2.26 mm (0.0890 in.) 2.29 mm (0.0902 in.) 2.32 mm (0.0913 in.) 2.35 mm (0.0925 in.) 2.40 mm (0.0945 in.) 2.45 mm (0.0965 in.) 2.50 mm (0.0984 in.) 2.55 mm (0.1004 in.) 2.60 mm (0.1024 in.) 2.65 mm (0.1043 in.) 2.70 mm (0.1063 in.) |
| 1st and reverse brake piston stroke | Standard | 0.791 to 1.489 mm (0.031 to 0.057 in.) |
| Input shaft end play | Standard | 0.3 to 0.9 mm (0.012 to 0.035 in.) |
| Transaxle housing oil seal drive in depth | Standard | 3.1 mm (0.122 in.) |
| Transaxle case oil seal drive in depth | Standard | 3.1 mm (0.122 in.) |
| Oil Pump | ||
| Stator shaft inside diameter | Standard Maximum | 21.500 to 21.526 mm (0.84646 to 0.84748 in.) 21.526 mm (0.84748 in.) |
| Oil pump body inside diameter | Standard Maximum | 38.113 to 38.138 mm (1.50050 to 1.50149 in.) 38.138 mm (1.50149 in.) |
| Oil pump clearance (Driven gear to drive gear clearance) | Standard Maximum | 0.07 to 0.15 mm (0.0028 to 0.0059 in.) 0.15 mm (0.0059 in.) |
| Oil pump clearance (Driven gear to oil pump body clearance) | Standard Maximum | 0.10 to 0.15 mm (0.0039 to 0.0059 in.) 0.15 mm (0.0059 in.) |
| Oil pump clearance (Side clearance) | Standard Maximum | 0.02 to 0.05 mm (0.0008 to 0.0020 in.) 0.05 mm (0.0020 in.) |
| Front oil pump oil seal drive in depth | Standard | -0.15 to 0.15 mm (-0.006 to 0.006 in.) |
| Input Shaft | ||
| Forward clutch return spring free length | Standard | 21.69 mm (0.8540 in.) |
| Forward clutch pack clearance | Standard | 1.406 to 1.806 mm (0.05535 to 0.07110 in.) |
| Forward clutch flange thickness | - 1 2 3 | 3.00 mm (0.1181 in.) 3.20 mm (0.1260 in.) 3.40 mm (0.1339 in.) 3.60 mm (0.1417 in.) |
| Second Brake Piston | ||
| 2nd brake piston return spring free length | Standard | 14.65 mm (0.5768 in.) |
| Intermediate Shaft | ||
| Direct clutch return spring free length | Standard | 32.9 mm (1.2953 in.) |
| Reverse clutch pack clearance | Standard | 0.86 to 1.26 mm (0.0339 to 0.0496 in.) |
| Reverse clutch flange thickness | - 1 2 3 | 3.0 mm (0.118 in.) 3.2 mm (0.126 in.) 3.4 mm (0.134 in.) 3.6 mm (0.142 in.) |
| Direct clutch pack clearance | Standard | 0.62 to 1.02 mm (0.0244 to 0.0402 in.) |
| Direct clutch flange thickness | - 1 2 3 | 3.0 mm (0.118 in.) 3.2 mm (0.126 in.) 3.4 mm (0.134 in.) 3.6 mm (0.142 in.) |
| Transaxle Rear Cover | ||
| Overdrive brake return spring free length | Standard | 17.88 mm (0.7039 in.) |
| Transaxle rear cover needle roller bearing depth | Standard | 25.2 mm (0.992 in.) |
| Valve Body | ||
| Shift solenoid valve S1 resistance | Standard | 11 to 15 Ω at 20°C (68°F) |
| Shift solenoid valve S2 resistance | Standard | 11 to 15 Ω at 20°C (68°F) |
| Shift solenoid valve ST resistance | Standard | 11 to 15 Ω at 20°C (68°F) |
| Shift solenoid valve SLT resistance | Standard | 5.1 to 5.5 Ω at 20°C (68°F) |
| Shift solenoid valve SL resistance | Standard | 11 to 15 Ω at 20°C (68°F) |
| Differential Case | ||
| Side gear backlash | Standard | 0.05 to 0.20 mm (0.0020 to 0.0079 in.) |
| Thrust washer thickness | - - - - - - | 0.95 mm (0.0374 in.) 1.00 mm (0.0394 in.) 1.05 mm (0.0413 in.) 1.10 mm (0.0433 in.) 1.15 mm (0.0453 in.) 1.20 mm (0.0472 in.) |