LUGGAGE COMPARTMENT DOOR (for Sedan) > DISASSEMBLY |
| 1. REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler) |
![]() |
Disconnect the center stop light connector.
Remove the 2 bolts.
![]() |
Apply protective tape to the luggage compartment door panel in the periphery of the rear spoiler.
Using an infrared light, heat the adhesive tape remaining on the rear spoiler.
Tie both piano wire ends to wooden blocks or similar objects.
![]() |
Cut the adhesive tape by pulling the piano wire alternatively toward you.
When reusing the rear spoiler, set the wooden blocks or similar objects along the body to avoid damaging the rear spoiler end portion.
![]() |
Disengage the 2 clips and remove the rear spoiler.
| 2. REMOVE HIGH MOUNTED STOP LIGHT (w/ Rear Spoiler) |
![]() |
Tie a piece of string to the tip of the wire harness.
Remove the 2 screws and the high mounted stop light.
| 3. REMOVE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY |
![]() |
Remove the snap ring in the direction indicated by the arrow and remove the luggage compartment door lock link.
![]() |
Disconnect the connector.
Disengage the claw and pull up the protector lid in the direction indicated by the arrow.
![]() |
Remove the luggage door lock control cable.
Remove the 2 bolts and the luggage compartment door lock assembly.
| 4. REMOVE LUGGAGE COMPARTMENT LOCK CYLINDER |
![]() |
Remove the 2 nuts and the luggage compartment lock cylinder.
| 5. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY |
![]() |
Remove the 2 nuts.
Disengage the 3 clips and remove the luggage compartment door outside garnish.
| 6. REMOVE LICENSE PLATE LIGHT ASSEMBLY |
![]() |
Pull the license plate light assembly in the direction indicated by arrow 1, shown in the illustration. Disengage claw B by pulling claw A toward you while flexing it and remove the license plate light assembly.
![]() |
Turn the license plate light socket and bulb, in the directions indicated by the arrow in the illustration, to remove them.
Remove the license plate light bulb from the light socket.
| 7. REMOVE NO. 6 LUGGAGE COMPARTMENT DOOR NAME PLATE |
![]() |
Apply protective tape, as shown in the illustration.
Using an infrared light, heat the No. 6 luggage compartment door name plate.
![]() |
Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 6 luggage compartment door name plate.
Remove the protective tape.
| 8. REMOVE NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE |
![]() |
Apply protective tape, as shown in the illustration.
Using an infrared light, heat the No. 2 luggage compartment door name plate.
![]() |
Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 2 luggage compartment door name plate.
Remove the protective tape.
| 9. REMOVE SYMBOL EMBLEM |
![]() |
Apply protective tape, as shown in the illustration.
Using an infrared light, heat the symbol emblem.
![]() |
Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the symbol emblem.
Remove the protective tape.
| 10. REMOVE LUGGAGE COMPARTMENT FLOOR MAT |
![]() |
Remove the luggage compartment floor mat.
| 11. REMOVE SPARE WHEEL COVER ASSEMBLY |
![]() |
Remove the spare wheel cover.
| 12. REMOVE DECK SIDE BOX DOOR RH |
![]() |
Remove the deck side box door RH.
| 13. REMOVE DECK SIDE BOX DOOR LH |
| 14. REMOVE DECK FLOOR BOX RH |
![]() |
Remove the deck floor box RH.
| 15. REMOVE DECK FLOOR BOX LH |
| 16. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Disengage the 8 claws and 2 clips and remove the rear floor finish plate.
| 17. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH |
![]() |
Disengage the 5 clips and remove the luggage compartment trim cover inner RH.
| 18. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH |
| 19. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD |
![]() |
Remove the luggage compartment trim inner pad.
| 20. REMOVE LUGGAGE COMPARTMENT DOOR WEATHERSTRIP |
![]() |
Remove the luggage compartment door weatherstrip.