REAR SEAT OUTER BELT ASSEMBLY (for Sedan) > INSTALLATION |
| 1. INSTALL SEAT BELT HOLE SEAL |
![]() |
Engage the 2 claws and install the seat belt hole seal.
| 2. INSTALL REAR SEAT OUTER BELT ASSEMBLY |
![]() |
Check the angle of inclination required to lock the retractor.
Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction.
Also, check that the belt locks when the inclination of the retractor is 45° or more.
![]() |
Insert the hook into the body hole and install the retractor with the bolt.
![]() |
Engage the 2 claws and install the anchor plate.
Tighten the bolt.
Check that the ELR locks.
With the belt installed, check that the belt locks when it is pulled out quickly.
If the operation is not as specified, replace the rear seat outer belt.
| 3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
for 3 Point Type Rear Center Seat Belt:
Engage the 5 claws and install the package tray trim.
Install the 4 clips.
![]() |
for 2 Point Type Rear Center Seat Belt:
Engage the 5 claws and install the package tray trim.
Install the 3 clips.
| 4. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY (w/o Rear Spoiler) |
![]() |
Connect the connector.
Engage the 4 claws and install the high mounted stop light assembly.
| 5. INSTALL ROOF SIDE INNER GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Install a new special clip and the clip onto the roof side inner garnish.
Engage the 4 clips and the claw and install the roof side inner garnish.
![]() |
w/o Curtain Shield Airbag:
Engage the 4 clips and the claw and install the roof side inner garnish.
| 6. INSTALL ROOF SIDE INNER GARNISH LH |
| 7. INSTALL REAR SEAT SIDE COVER RH |
![]() |
Engage the 2 clips and the 4 claws and install the rear seat side cover.
| 8. INSTALL REAR SEAT SIDE COVER LH |
| 9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the location mark with the paint mark first, and install the rear door opening trim weatherstrip, as shown in the illustration.
| Area | Color |
| RH side | Green |
| LH side | Red |
| 10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 11. INSTALL REAR DOOR SCUFF PLATE RH |
![]() |
Engage the 7 claws and install the rear door scuff plate.
| 12. INSTALL REAR DOOR SCUFF PLATE LH |
| 13. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type) |
![]() |
Install the luggage compartment trim inner pad.
| 14. INSTALL SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type) |
![]() |
Install the spare wheel cover.
| 15. INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type) |
![]() |
Install the luggage compartment floor mat.
| 16. INSTALL REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type) |
![]() |
Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.
![]() |
Install the rear seatback cover with the 2 clips.
Pull up the rear seatback.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
for 3 Point Type Rear Seat Belt:
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 17. INSTALL REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type) |
![]() |
Insert the 2 hooks into the rear seatback frame hole and install the rear seatback tightening the 2 bolts in the sequence shown in the illustration.
![]() |
Install the rear seatback cover with the 2 clips.
Pull up the rear seatback.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
| 18. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type) |
![]() |
Engage the 3 hooks and install the rear seatback.
Tighten the 3 bolts.
![]() |
Install the rear seat outer belt into the rear seat shoulder belt guide.
for 3 Point Type Rear Center Seat belt:
Install the rear center seat outer belt into the rear center seat shoulder belt guide.
| 19. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY |
for 60/40 Split Seat Type:
Install the rear seat cushion cover pad sub-assembly .
for Fixed Seat Type:
Install the rear seat cushion cover pad sub-assembly .
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/o Rear Spoiler) |