WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS > PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED



Procedures Necessary when ECU or Other Parts are Replaced 
Replacement Part
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
Note
ECM (for 1ND-TV)
  1. Learning values save
  2. Learning values write
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
Injector assembly (for 1ND-TV)
  1. Injector Compensation
  2. Pilot Quantity Learning Values Reset
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
Air fuel ratio sensor (for 1ND-TV)
A/F Sensor Compensation Reset
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
DPF catalyst (for 1ND-TV)
DPF Deterioration Record Clear
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
Engine assembly (for 1ND-TV)
  1. Injector Compensation
  2. Pilot Quantity Learning Values Reset
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
  1. Diesel throttle body assembly (for 1ND-TV)
  2. Electric EGR valve assembly (for 1ND-TV)
  3. Turbo charger sub-assembly (for 1ND-TV)
  1. Learning values save
  2. Learning values write
Engine starting
-
  1. ECM (for 1KR-FE)
  2. Throttle body assembly (for 1KR-FE)
Input the learning value of the throttle position sensor
Rough idle
-
  1. Throttle with motor body assembly (for 1NR-FE)
  2. Engine assembly (for 1NR-FE)
  3. Cylinder head (for 1NR-FE)
  4. Camshaft (for intake or exhaust side) (for 1NR-FE)
  5. Camshaft timing gear assembly (for intake or exhaust side) (for 1NR-FE)
  6. Piston or piston ring (for 1NR-FE)
  7. Mass air flow meter (for 1NR-FE)
  8. Fuel injector assembly (for 1NR-FE)
  9. Fuel pump (for 1NR-FE)
  10. Air fuel ratio sensor (for 1NR-FE)
  11. Engine coolant temperature sensor (for 1NR-FE)
  12. Spark plug
  13. Ignition coil assembly (for 1NR-FE)
  14. EGR valve assembly (for 1NR-FE)
  15. Knock sensor (for 1NR-FE)
Inspection after repairs
-
-
Engine stop and start ECU
  1. Read number of starter operations
  2. Register number of starter operations
  3. Clear A/C information
  4. Register A/C information
  5. Clear the zero point calibration data
  6. Perform zero point calibration of the yaw rate and deceleration sensor
Stop and Start System
-
Starter assembly
Clear number of starter operations
Stop and Start System
-
  1. Transaxle assembly (EC65A)
  2. Transaxle parts (inside gear box) (EC65A)
  3. TCM (EC65A)
  4. Shift and select actuator (EC65A)
  5. Shift stroke sensor (EC65A)
  6. Select stroke sensor (EC65A)
  7. Clutch actuator (EC65A)
  8. Clutch stroke sensor (EC65A)
  9. Clutch disc and clutch cover (EC65A)
  10. Clutch release with bearing cylinder assembly (EC65A)
  11. Flywheel (EC65A)
  12. Crankshaft (EC65A)
  1. Initialization of Multi-Mode Manual Transaxle System
  2. Learning of Multi-Mode Manual Transaxle System
  3. Synchronization Position Calibration
Warning light comes on
-
  1. Continuously variable transaxle assembly (K411)
  2. Oil pressure sensor (K411)
  3. ECM
  1. Clear the CVT learned values
  2. Deceleration sensor 0 point calibration
  3. CVT oil pressure calibration
  4. Air bleeding of the electric air pump
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
w/ VSC
  1. Center airbag sensor assembly
  1. Clear the CVT learned values
  2. Deceleration sensor 0 point calibration
  3. CVT oil pressure calibration
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
w/ VSC
  1. Brake actuator assembly (Skid control ECU)
  1. Deceleration sensor 0 point calibration
  1. Warning light comes on
  2. The deterioration of fuel efficiency
-
  1. Power steering ECU assembly
  1. Steering column assembly (containing the torque sensor)
  1. Torque sensor zero point calibration
  2. Assist map writing
  1. Warning light comes on
  2. Power assist stops
-
w/ entry and start system
  1. Certification ECU
  2. ID code box
  3. Steering lock ECU
  4. Electrical key transmitter
  5. ECM
  1. Code registration
  2. ECU communication ID registration
  1. Wireless door lock control system
  2. Engine start
  3. Entry operation
  4. Steering lock and unlock
Refer to the Service Bulletin for the registration procedure.
w/o entry and start system
  1. Transponder key ECU
  2. Door control receiver
  3. Key
  4. ECM
ECU communication ID registration
  1. Wireless door lock control system
  2. Engine start
Refer to the Service Bulletin for the registration procedure.
Oil maintenance management system (for 1ND-TV)
Oil maintenance information mode reset operation
Oil change reminder light is on
-
Power window regulator motor
Motor initialization
  1. Jam protection function
  2. Power window control system
-