FIT STANDARD / ADJUSTMENT METHOD > ADJUSTMENT |
| INSPECT HOOD SUB-ASSEMBLY |
Check that the clearance measurements are within the standard ranges.

| Area | Measurement | Area | Measurement |
| A | 2.0 to 6.0 mm (0.0787 to 0.236 in.) | D | 2.3 to 5.3 mm (0.0905 to 0.208 in.) |
| B | 11.0 mm (0.433 in.) | E | 1.2 to 5.2 mm (0.0472 to 0.204 in.) |
| C | 5.0 mm (0.196 in.) | - | - |
| ADJUST HOOD SUB-ASSEMBLY |
![]() |
Loosen the 4 hood side hinge bolts.
Move the hood to adjust the clearance to within the standard range.
Tighten the 4 hood side hinge bolts after the adjustment.
![]() |
Adjust the height of the hood front end by turning the 2 center hood cushions.
![]() |
Adjust the hood lock.
Loosen the 3 bolts.
Adjust the hood lock position so that the striker can enter it smoothly.
Tighten the 3 bolts after the adjustment.
| INSPECT FRONT DOOR |
Check that the clearance measurements are within the standard ranges.

| Area | Measurement | Area | Measurement |
| A | 3.0 to 6.0 mm (0.118 to 0.232 in.) | F | 3.0 mm (0.118 in.) |
| B | 2.1 to 5.1 mm (0.0826 to 0.200 in.) | G | 3.6 to 6.6 mm (0.141 to 0.259 in.) |
| C | 3.5 to 6.5 mm (0.137 to 0.255 in.) | H | -1.5 to 1.5 mm (-0.0590 to 0.0590 in.) |
| D | 2.9 mm (0.114 in.) | I | 5.5 to 8.5 mm (0.216 to 0.334 in.) |
| E | 3.5 to 6.5 mm (0.137 to 0.255 in.) | J | 5.5 to 8.5 mm (0.216 to 0.334 in.) |
| ADJUST FRONT DOOR |
![]() |
Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.
Tighten the body side hinge bolts after the adjustment.
![]() |
Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.
Tighten the door side hinge bolts after the adjustment.
![]() |
Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.
Using a "TORX" socket wrench T40, tighten the striker mounting screws after the adjustment.
| INSPECT REAR DOOR |
Check that the clearance measurements are within the standard ranges.

| Area | Specified Condition | Area | Specified Condition |
| A | 3.6 to 6.6 mm (0.141 to 0.259 in.) | D | 1.2 to 4.2 mm (0.0472 to 0.165 in.) |
| B | -1.5 to 1.5 mm (-0.0590 to 0.0590 in.) | E | 2.8 to 5.8 mm (0.110 to 0.228 in.) |
| C | 3.5 to 6.5 mm (0.137 to 0.255 in.) | F | 5.5 to 8.5 mm (0.216 to 0.334 in.) |
| ADJUST REAR DOOR |
![]() |
Using SST, adjust the door horizontally and vertically by loosening the body side hinge bolts.
Tighten the body side hinge bolts after the adjustment.
![]() |
Using SST, adjust the door horizontally and vertically by loosening the door side hinge bolts.
Tighten the door side hinge bolts after the adjustment.
![]() |
Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.
| INSPECT BACK DOOR |
Check that the clearance measurements are within the standard ranges.

| Area | Measurement | Area | Measurement |
| A | 6.0 to 9.0 mm (0.236 to 0.354 in.) | I | 3.0 to 8.0 mm (0.118 to 0.314 in.) |
| B | -0.5 to 2.5 mm (0.0196 to 0.0984 in.) | J | 4.0 to 6.0 mm (0.157 to 0.236 in.) |
| C | 6.0 to 9.0 mm (0.236 to 0.354 in.) | K | -1.5 to 1.5 mm (-0.0590 to 0.0590 in.) |
| D | -0.2 to 2.8 mm (0.00787 to 0.110 in.) | L | 3.2 to 7.2 mm 0.125 to 0.283 in.) |
| E | 4.1 to 7.1 mm (0.161 to 0.279 in.) | M | 3.2 to 7.2 mm (0.125 to 0.283 in.) |
| F | 1.3 to 4.3 mm (0.0511 to 0.169 in.) | N | 3.4 to 7.4 mm (0.133 to 0.291 in.) |
| G | 4.5 to 7.5 mm (0.177 to 0.295 in.) | O | 3.8 to 7.8 mm (0.149 to 0.307 in.) |
| H | -1.0 to 2.0 mm (-0.0393 to 0.0787 in.) | - | - |
| ADJUST BACK DOOR |
![]() |
Adjust the door position.
Horizontally and vertically adjust the door by loosening the door side hinge bolts.
![]() |
Adjust the striker position.
Using a "TORX" socket wrench T40, adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a plastic hammer.
Using a "TORX" socket wrench T40, tighten the striker mounting bolts after the adjustment.