AIR CONDITIONING SYSTEM > GENERAL



OUTLINE
  1. A Manual air conditioning system or automatic air conditioning system is used.

  2. A manual air conditioning system employing the boost vent, which is not equipped with the heater radiator unit sub-assembly that uses an engine coolant heater, has been provided on some models.


SPECIFICATION
  1. Performance

    Destination
    Australia
    G.C.C. Countries
    General Countries
    Air Conditioning Type
    Manual
    Automatic
    Manual
    Automatic
    Manual
    Heater
    Heater Output
    W
    4600
    ←
    4800*1
    4800
    4600*1
    Air Flow Volume
    m3/h
    280
    ←
    300*1
    300
    280*1
    Power Consumption
    W
    170
    ←
    200*1
    200
    170*1
    Cooler
    Cooling Capacity
    W
    4430
    ←
    4570
    ←
    4430*2 / 4450*3
    Air Flow Volume
    m3/h
    420
    ←
    465
    ←
    420*2 / 430*3
    Power Consumption
    W
    210
    ←
    245
    ←
    210*2 / 230*3

    1. *1: Models without boost vent
    2. *2: RHD models
    3. *3: LHD models

  2. Ventilation and Heater Radiator Unit Sub-assembly

    Destination
    Australia
    G.C.C. Countries
    General Countries
    Heater Radiator Unit Sub-assembly
    Type
    Straight Flow Aluminum (SFA)-II
    Straight Flow Aluminum (SFA)-II*1
    Straight Flow Aluminum (SFA)-II*1
    Size: W x H x L
    mm (in.)
    201.5 x 140 x 27 (7.9 x 5.5 x 1.1)
    201.5 x 140 x 27 (7.9 x 5.5 x 1.1)*1
    201.5 x 140 x 27 (7.9 x 5.5 x 1.1)*1
    Fin Pitch
    mm (in.)
    1.8 (0.07)
    1.8 (0.07)*1
    1.8 (0.07)*1
    Blower with Fan Motor Sub-assembly
    Motor Type
    K62-12.5T
    K70-10T
    K62-11.5T*2 / K62-12.5T*3
    Fan Type
    Semi Sirocco
    ←
    ←
    Fan Size: Dia. x H
    mm (in.)
    145 x 65 (5.7 x 2.6)
    ←
    ←

    1. *1: Models without boost vent
    2. *2: LHD models
    3. *3: RHD models

  3. Air Conditioning

    Destination
    Australia
    G.C.C. Countries
    General Countries
    Cooler Condenser Assembly
    Type
    Multi-Flow (MF)-IV (Sub Cool)
    ←
    ←
    Size: W x H x L
    mm (in.)
    520 x 325.4 x 16 (20.5 x 12.8 x 0.6)
    680 x 325.4 x 16 (26.8 x 12.8 x 0.6)
    520 x 325.4 x 16 (20.5 x 12.8 x 0.6)
    Fin Pitch
    mm (in.)
    2.75 (0.1)
    3.15 (0.1)
    2.75 (0.1)
    No. 1 Cooler Evaporator Sub-assembly
    Type
    Revolutionary super-Slim structure (RS)
    ←
    ←
    Size: W x H x L
    mm (in.)
    199.3 x 231 x 38 (7.8 x 9.1 x 1.5)
    ←
    ←
    Fin Pitch
    mm (in.)
    2.6 (0.1)
    ←
    ←
    Compressor with Pulley Assembly
    Type
    5TSE10C
    ←
    ←
    Pulley
    Damper Limiter (DL)
    ←
    ←
    Refrigerant
    Type
    HFC134a
    ←
    ←
    Charge Volume
    g
    360+/-30
    380+/-30
    360+/-30
    Clean Air Filter
    High Efficiency Type
    ←
    ←


MAIN FEATURES
  1. The air conditioning system has the following features:

    Item
    Outline
    High Performance
    1. Neural network control is used so passengers can control the air conditioning accurately for maximum comfort.*1
    2. A high efficiency type clean air filter is used as the clean air filter.
    3. The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.*1
    Lightweight
    A bus connector (air conditioning harness assembly) with a built-in IC is used in a lightweight wire harness design with a reduced number of wires. The use of this connector means that pulse pattern type servo motors are used.*1
    Compact
    1. A semi-center location air conditioning unit in which the No. 1 cooler evaporator sub-assembly and heater radiator unit sub-assembly*2 are placed in the vehicle's longitudinal direction is used.
    2. A blower motor with a built-in blower motor controller is used in a compact construction.*1
    Others
    1. The following parts are used to ensure high cooling or heating performance while realizing a compact and lightweight construction.
      1. Revolutionary super-Slim structure (RS) type No. 1 cooler evaporator sub-assembly
      2. Straight Flow Aluminum (SFA)-II type heater radiator unit sub-assembly*2
      3. Multi-Flow (MF)-IV type cooler condenser assembly.
      4. Continuously variable capacity type compressor with pulley assembly (5TSE10C type)

    1. *1: Models with automatic air conditioning system
    2. *2: Models without boost vent