AIRBAG SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The airbag system mainly consists of the parts listed in the table below.

    Components
    Outline
    Airbag
    Mainly consists of an inflator and a bag. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to deploy the bag.
    Front Seat Outer Belt Assembly
    Mainly consists of an inflator and a seat belt. Upon receiving a deployment signal from the airbag sensor assembly, the inflator generates gas to retract the seat belt.
    Airbag Sensor
    Detects the deceleration of the vehicle during a collision, and transmits the signal to the airbag sensor assembly, from which the airbag sensor assembly determines whether ignition is necessary.
    Airbag Sensor Assembly
    1. Detects the deceleration of the vehicle during a collision, determines whether ignition is necessary based on the signals from each airbag sensor, and transmits deployment signals to each airbag and seat belt pretensioner.
    2. Provides initial check and diagnosis function.
    SRS Warning Light
    Provided in the combination meter assembly and comes on when the airbag system malfunctions.


OPERATING CONDITION


  1. Ignition Condition

    1. Deceleration sensors used for the airbag system are installed on various parts on the vehicle and transmit the deceleration data of each part during a collision.

    2. Depending on the situation, the airbag sensor assembly sends a deployment signal to each airbag based on the information from each sensor.



    3. Frontal collision signals are produced based on the information from the airbag sensor assembly and the front airbag sensor. The frontal collision signals are used to deploy the steering wheel pad assembly, instrument panel passenger airbag without door assembly, lower No. 1 instrument panel airbag assembly and to activate the seat belt pretensioners.


      Y111934E01



    4. Side or side rear collision signals are produced based on the information from the airbag sensor assembly and side airbag sensor assembly*1, No. 2 side airbag sensor assembly or door side airbag sensor assembly*2. Side or side rear collision signals are used to deploy the front seat side airbag assembly*3, curtain shield airbag assembly and to activate the seat belt pretensioner*3.

      1. *1: 5-door models
      2. *2: 3-door models

      HINT:
      *3: If a collision signal is transmitted from a No. 2 side airbag sensor assembly only, a front seat side airbag assembly will not deploy and also a seat belt pretensioner will not be activated.


      Y111935E01


SYSTEM CONTROL


  1. Airbag for Frontal Collision



    1. For frontal collisions, there are 3 airbags and 2 seat belt pretensioners: a steering wheel pad assembly, instrument panel passenger airbag without door assembly, lower No. 1 instrument panel airbag assembly, front seat outer belt assembly LH and front seat outer belt assembly RH. The deployment of the airbags and the activation of the seat belt pretensioners occur simultaneously.


      Y111984E01



  2. Airbag for Side or Side Rear Collision



    1. For a side collision, if the side airbag sensor assembly*1 and door side airbag sensor assembly*2 detect an impact, it inform the airbag sensor assembly, and the airbag sensor assembly causes the front seat side airbag assembly, curtain shield airbag assembly and seat belt pretensioner to be deployed and operated simultaneously.

      1. *1: 5-door models
      2. *2: 3-door models

      Y111937E01


      Y111992E01



    2. For a side rear collision, if the No. 2 side airbag sensor assembly detects an impact, it informs the airbag sensor assembly via the side airbag sensor assembly, and the airbag sensor assembly causes the curtain shield airbag assembly to be deployed.


      Y111938E01


      Y111993E01



  3. Primary Check Illumination Control



    1. After the ignition switch is turned ON, the airbag sensor assembly illuminates the SRS warning light in the combination meter assembly for approximately 6 seconds and conducts the primary check. During the primary check, the ignition of airbags is prohibited and a diagnosis of the airbag sensor assembly is performed. If trouble is detected during the primary check, the SRS warning light remains on even after the 6 seconds have elapsed. See the illustration below.


      Y111985E01


CONSTRUCTION
  1. Steering Wheel Pad Assembly and Instrument Panel Passenger Airbag without Door Assembly

    1. The steering wheel pad assembly and instrument panel passenger airbag without door assembly mainly consist of an inflator and a bag.

  2. Lower No. 1 Instrument Panel Airbag Assembly

    1. The lower No. 1 instrument panel airbag assembly consists of an airbag door, an inflator and a bag.

  3. Curtain Shield Airbag Assembly

    1. Curtain shield airbag assemblies that extend from the front pillar to the roof side rail are installed. Each curtain shield airbag assembly consists of an inflator and a bag.

  4. Front Seat Side Airbag Assembly

    1. Front seat side airbag assemblies are installed in the seat backs of the driver seat and the front passenger seat. Each front seat side airbag assembly consists of an inflator, a bag and a cover.



  5. Front Airbag Sensor



    1. A deceleration sensor is enclosed in the front airbag sensor. Based on the deceleration of the vehicle during a front collision, a distortion is created in the sensor and converted into an electrical signal. Accordingly, the extent of the initial collision can be detected in detail.


      Y111919E01



  6. Side Airbag Sensor Assembly*1, No. 2 Side Airbag Sensor Assembly and Door Side Airbag Sensor Assembly*2



    1. A deceleration sensor is enclosed in the side airbag sensor assembly*1, No. 2 side airbag sensor assembly and door side airbag sensor assembly*2. Based on the deceleration of the vehicle during a side or side rear collision, a distortion is created in the sensor and converted into an electrical signal.

      1. *1: 5-door models
      2. *2: 3-door models

      Y111940E01


      Y111994E01


DIAGNOSIS
  1. If the airbag sensor assembly detects a malfunction in the airbag system, the airbag sensor assembly stores the malfunction data in memory, in addition to illuminating the SRS warning light.

  2. There are 2 types of Diagnostic Trouble Code (DTC) for the airbag system: 5-digit and 2-digit.

  3. The 5-digit DTC can be read by connecting the intelligent tester to DLC3.

  4. The 2-digit DTC can be read by connecting the SST (09843-18040) to the TC and CG terminals of the DLC3 and reading the blinking of the SRS warning light.



  5. If the SRS airbag deploys, the airbag sensor assembly will turn on the SRS warning light. However, different from the ordinary diagnosis function, a DTC will not be stored. The SRS warning light cannot be turned off. It is necessary to replace the airbag sensor assembly with a new one.


    Y100869E01