ENGINE UNIT > GENERAL



OUTLINE
  1. The 1NZ-FE engine is a 1.5-liter, 16-valve DOHC, in-line 4-cylinder gasoline engine.



  2. The Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS) and Electronic Throttle Control System-intelligent (ETCS-i) are used on this engine in order to realize high performance, quietness, fuel economy and clean emission.


    W104600


SPECIFICATION

Engine Type
1NZ-FE
No. of Cyls. and Arrangement
4-cylinder, In-line
Valve Mechanism
16-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber
Pentroof Type
Flow of Intake and Exhaust Gasses
Cross-Flow
Fuel System
SFI
Ignition System
DIS
Displacement
1497 cm3 (91.3 cu. in.)
Bore x Stroke
75.0 mm x 84.7 mm (2.95 in. x 3.33 in.)
Compression Ratio
10.5 : 1
Max. Output
EEC
80 kW @ 6000 rpm
Max. Torque
EEC
141 N*m @ 4200 rpm
Valve Timing
Intake
Open
33°BTDC to 7°ATDC
Closed
12°ABDC to 52°ABDC
Exhaust
Open
42°BBDC
Closed
2°ATDC
Firing Order
1 - 3 - 4 - 2
Fuel
Unleaded Gasoline
Research Octane Number (RON)
91 or higher
Oil Grade
API grade SL "Energy-Conserving", SM "Energy-Conserving" or ILSAC multigrade engine oil
Emission Regulation
EURO 4
Engine Service Mass* (Reference)
M/T
89.6 kg (197.5 lb)
A/T
79.6 kg (175.5 lb)

HINT:
*: Weight shows the figure with oil and water fully filled.


W105305E01


MAIN FEATURES
  1. The 1NZ-FE engine has achieved the following performance through the use of the items listed below.

    1. High performance and fuel economy

    2. Low noise and vibration

    3. Lightweight and compact design

    4. Good serviceability

    5. Clean emission and fuel economy

      Section
      Item
      (1)
      (2)
      (3)
      (4)
      (5)
      Engine Proper
      An aluminum cylinder block sub-assembly is used.
      -
      -
      ○
      -
      -
      An offset crankshaft is used.
      ○
      ○
      -
      -
      ○
      A taper squish shape is used for the top of the pistons.
      ○
      -
      -
      -
      ○
      Valve Mechanism
      A chain sub-assembly and no. 1 chain tensioner assembly are used.
      ○
      -
      ○
      ○
      -
      The Variable Valve Timing-intelligent (VVT-i) system is used.
      ○
      -
      -
      -
      ○
      Intake and Exhaust System
      A plastic intake manifold is used.
      -
      -
      ○
      -
      -
      A linkless type throttle body is used.
      -
      -
      ○
      ○
      -
      A stainless steel exhaust manifold is used.
      -
      -
      ○
      -
      -
      2 Three-Way Catalytic converters (TWCs) are used.
      -
      -
      -
      -
      ○
      A rearward exhaust layout is used.
      -
      -
      -
      -
      ○
      Fuel System
      12-hole type fuel injector assemblies are used.
      ○
      -
      -
      -
      -
      A fuel returnless system is used.
      -
      -
      ○
      ○
      ○
      Quick connectors are used to connect the fuel hoses and fuel pipes.
      -
      -
      -
      ○
      -
      Ignition System
      A Direct Ignition System (DIS) is used.
      ○
      -
      -
      ○
      ○
      Engine Control System
      The Electronic Throttle Control System-intelligent (ETCS-i) is used.
      ○
      -
      -
      -
      ○
      The non-contact sensor is used in the throttle position sensor and accelerator pedal position sensor.
      ○
      -
      -
      -
      -