Home › Drivetrain ยท CLUTCH › CLUTCH PEDAL (for RHD)

CLUTCH PEDAL (for RHD) > ADJUSTMENT

for Preparation Click here



1. INSPECT AND ADJUST CLUTCH PEDAL HEIGHT
  1. Pull back the floor carpet.



    C235137E01
  1. Check that the pedal height is correct.
    Text in Illustration 
    *1
    Clutch Pedal Stopper Bolt
    *2
    Lock Nut (Pedal height adjust point)
    *a
    Pedal height from floor

    Pedal height from floor:
    for 1NZ-FE:
    159.3 to 169.3 mm (6.272 to 6.665 in.)
    for 2NZ-FE:
    144.4 to 154.4 mm (5.685 to 6.079 in.)

  1. If the pedal height is not as specified, adjust it as follows.

    1. Loosen the lock nut and turn the clutch pedal stopper bolt until the correct height is obtained.

    2. Tighten the lock nut.

      Torque:
      16 N*m{ 160 kgf*cm , 12 ft.*lbf }

  1. Install the floor carpet.

  1. w/ Cruise Control System:

    1. Check the No. 2 clutch start switch clearance .



2. INSPECT AND ADJUST PEDAL FREE PLAY AND PUSH ROD PLAY


    C235138E01
  1. Check that the pedal free play and push rod play are correct.
    Text in Illustration 
    *1
    Push Rod
    *2
    Lock Nut (Push rod play and free play adjust point)
    *a
    Push rod play
    *b
    Pedal free play

    1. Depress the pedal until clutch resistance begins to be felt.

      Pedal free play:
      5.0 to 15.0 mm (0.197 to 0.591 in.)

    2. Gently depress the pedal until resistance begins to increase a little.

      Push rod play at pedal top:
      1.0 to 5.0 mm (0.039 to 0.197 in.)

  1. If necessary, adjust the pedal free play and push rod play.

    1. Loosen the lock nut and turn the push rod until the correct free play and push rod play are obtained.

    2. Tighten the lock nut.

      Torque:
      12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    3. After adjusting the pedal free play, check the pedal height.



3. INSPECT CLUTCH RELEASE POINT


    C235139E01
  1. Check the clutch release point.
    Text in Illustration 
    *a
    Full stroke end position
    *b
    From pedal stroke end position to release point
    *c
    Release point
    *d
    Pedal stroke

    1. Pull the parking brake lever and install wheel stoppers.

    2. Start the engine and run it at idle.

    3. Without depressing the clutch pedal, slowly move the shift lever into reverse until the gears come into contact.

    4. Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

      Standard distance:
      25 mm (0.984 in.) or more (From pedal stroke end position to release point)

      Pedal stroke (Reference):
      for 1NZ-FE:
      137 to 147 mm (5.394 to 5.787 in.)
      for 2NZ-FE:
      120 to 130 mm (4.724 to 5.118 in.)

      If the distance is not as specified, perform the following procedure:
      1. Check the pedal height.
      2. Check the push rod play and pedal free play.
      3. Bleed the clutch line.
      4. Check the clutch cover and clutch disc.