Home › Engine / Hybrid System · 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A258723E01

HINT:
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A74-20 (BATT) - B84-104 (E1)
Y - W-B
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
A74-2 (+B) - B84-104 (E1)
B - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
A74-1 (+B2) - B84-104 (E1)
B - W-B
Power source of ECM
Ignition switch ON
11 to 14 V
A74-3 (+BM) - B84-43 (ME01)
GR - BR
Power source of throttle actuator
Always
11 to 14 V
B84-85 (IGT1) - B84-104 (E1)
W - W-B
No. 1 ignition coil (ignition signal)
Idling
Pulse generation
(See waveform 1)
B84-84 (IGT2) - B84-104 (E1)
V - W-B
B84-83 (IGT3) - B84-104 (E1)
G - W-B
B84-82 (IGT4) - B84-104 (E1)
LG - W-B
B84-81 (IGF1) - B84-104 (E1)
Y - W-B
No. 1 ignition coil (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 1)
B84-122 (NE+) - B84-121 (NE-)
L - P
Crankshaft position sensor
Idling with warm engine
Pulse generation
(See waveform 2)
B84-99 (VV1+) - B84-121 (NE-)
W - P
Camshaft position sensor
Idling with warm engine
Pulse generation
(See waveform 2)
B84-108 (#10) - B84-45 (E01)
B - BR
Fuel injector assembly
Ignition switch ON
11 to 14 V
B84-107 (#20) - B84-45 (E01)
GR - BR
B84-106 (#30) - B84-45 (E01)
P - BR
Idling
Pulse generation
(See waveform 3)
B84-105 (#40) - B84-45 (E01)
L - BR
B84-109 (HT1A) - B84-86 (E03)
G - W-B
Heated oxygen sensor (sensor 1) heater
Ignition switch ON
11 to 14 V
B84-112 (OX1A) - B84-90 (EX1A)
B - V
Heated oxygen sensor (sensor 1)
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 4)
B84-47 (HT1B) - B84-86 (E03)
L - W-B
Heated oxygen sensor (sensor 2) heater
Ignition switch ON
11 to 14 V
B84-64 (OX1B) - B84-87 (EX1B)
B - GR
Heated oxygen sensor (sensor 2)
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
Pulse generation
(See waveform 5)
B84-110 (KNK1) - B84-111 (EKNK)
R - G
Knock sensor
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 6)
A74-8 (SPD) - B84-104 (E1)
V - W-B
Speed signal from combination meter assembly
Driving at 20 km/h (12 mph)
Pulse generation
(See waveform 7)
B84-97 (THW) - B84-96 (ETHW)
V - BR
Engine coolant temperature sensor
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
B84-65 (THA) - B84-88 (ETHA)
P - G
Intake air temperature sensor
Idling, Intake air temperature 20°C (68°F)
1.5 to 3.0 V
B84-118 (VG) - B84-116 (E2G)
GR - L
Mass air flow meter
Idling, Shift lever position neutral, A/C switch OFF
0.5 to 3.0 V
A74-24 (W) - B84-104 (E1)
B - W-B
MIL
Ignition switch ON
(MIL goes on)
Below 1.5 V
Idling
11 to 14 V
A74-48 (STA) - B84-104 (E1)
BR - W-B
Starter signal
Cranking
5.5 V or more
B84-52 (NSW) - B84-104 (E1)
BE - W-B
Clutch start switch signal*1
Park/neutral position switch signal*2
Ignition switch ON
(clutch pedal depressed)*1
Below 1.5 V
Ignition switch ON
(clutch pedal released)*1
11 to 14 V
Ignition switch ON
(shift lever in P, N)*2
Below 1.5 V
Ignition switch ON
(shift lever not in P, N)*2
11 to 14 V
Cranking
6 to 13 V
B84-115 (VTA1) - B84-91 (ETA)
Y - V
Throttle position sensor (for engine control)
Ignition switch ON, Throttle valve fully closed
0.5 to 1.1 V
Ignition switch ON, Throttle valve fully open
3.2 to 4.8 V
B84-114 (VTA2) - B84-91 (ETA)
GR - V
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, Throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON, Throttle valve fully open
4.6 to 5.0 V
B84-67 (VCTA) - B84-91 (ETA)
W - V
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
A74-57 (VCPA) - A74-59 (EPA)
G - V
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
A74-55 (VPA) - A74-59 (EPA)
R - V
Accelerator pedal position sensor (for engine control)
Ignition switch ON, Accelerator pedal released
0.5 to 1.1 V
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
A74-56 (VPA2) - A74-60 (EPA2)
L - B
Accelerator pedal position sensor (for sensor malfunctioning detection)
Ignition switch ON, Accelerator pedal released
1.2 to 2.0 V
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 4.7 V
A74-58 (VCP2) - A74-60 (EPA2)
W - B
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
B84-42 (M+) - B84-43 (ME01)
G - BR
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 8)
B84-41 (M-) - B84-43 (ME01)
BR - BR
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 9)
A74-36 (STP) - B84-104 (E1)
LG - W-B
Stop light switch assembly
Brake pedal depressed
11 to 14 V
Brake pedal released
Below 1.5 V
A74-35 (ST1-) - B84-104 (E1)
Y - W-B
Stop light switch assembly (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
Ignition switch ON, Brake pedal released
11 to 14 V
B84-49 (PRG) - B84-45 (E01)
L - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 10)
A74-7 (FC) - B84-45 (E01)
V - BR
Fuel pump control
Ignition switch ON
11 to 14 V
Idling
Below 1.5 V
A74-15 (TACH) - B84-104 (E1)
LG - W-B
Engine speed
Idling
Pulse generation
(See waveform 11)
A74-27 (TC) - B84-104 (E1)
L - W-B
Terminal TC of DLC 3
Ignition switch ON
11 to 14 V
B84-100 (OC1+) - B84-123 (OC1-)
BR - Y
Camshaft timing oil control valve assembly (OCV)
Idling
Pulse generation
(See waveform 12)
A74-41 (CANH) - B84-104 (E1)
L - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 13)
A74-49 (CANL) - B84-104 (E1)
W - W-B
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 14)
A74-31 (ELS1) - B84-104 (E1)
R - W-B
Electric load
Tail light switch on
7.5 to 14 V
Tail light switch off
Below 1.5 V
A74-33 (ELS2) - B84-104 (E1)
G - W-B
Electric load
Defogger switch on
7.5 to 14 V
Defogger switch off
Below 1.5 V
A74-21 (FANL) - B84-104 (E1)
R - W-B
Cooling fan relay
Ignition switch ON
Cooling fan not operated
11 to 14 V
Idling with A/C ON
or
High engine coolant temperature
Cooling fan operated
Below 1.5 V
A74-22 (FANH) - B84-104 (E1)
G - W-B
Cooling fan relay No. 2
Idling with high engine coolant temperature
Cooling fan operated at high speed
Below 1.5 V
B84-50 (ALT) - B84-104 (E1)
G - W-B
Generator assembly
Ignition switch ON
11 to 14 V
A74-28 (IGSW) - B84-104 (E1)
R - W-B
Ignition switch assembly
Ignition switch ON
11 to 14 V
A74-44 (MREL) - B84-104 (E1)
GR - W-B
EFI relay
Ignition switch ON
11 to 14 V
*1: for Manual Transaxle
*2: for Automatic Transaxle

WAVEFORM 1
A033447E06
Igniter Signal (IGT and IGF signal) 
ECM Terminal Name
CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A063955E49
Crankshaft Position Sensor and Camshaft Position Sensor Signal 
ECM Terminal Name
CH1: Between VV1+ and NE-
CH2: Between NE+ and NE-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 3
A093279E37
Fuel Injector Assembly Injection Signal 
ECM Terminal Name
Between #10 (to #40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 4
A005132E09
Heated Oxygen Sensor (sensor 1) Signal 
ECM Terminal Name
Between OX1A and EX1A
Tester Range
200 mV/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:
In the Data List, the items O2S B1S1 show the ECM input values of the heated oxygen sensor (sensor 1).


WAVEFORM 5
A088863E52
Heated Oxygen Sensor (sensor 2) Signal 
ECM Terminal Name
Between OX1B and EX1B
Tester Range
200 mV/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:
In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor (sensor 2).


WAVEFORM 6
A082985E22
Knock Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.


WAVEFORM 7
A005135E59
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 8
A208000E12
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 9
A245848E14
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 10
A205411E04
Purge VSV Signal 
ECM Terminal Name
Between PRG and E01
Tester Range
10 V/DIV., 20 ms./DIV.
Condition
Idling, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 11
A005138E24
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine rpm increases.


WAVEFORM 12
A093229E56
Camshaft Timing Oil Control Valve (OCV) Signal 
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 13
A086154E61
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 14
A086155E55
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.