DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic) |
|
| P2123 | VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is depressed (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more (b) VPA is between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 is 0.02 V or less (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less |
|
| Trouble Area | Accelerator Pedal Released | Accelerator Pedal Depressed | ||
| Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.7 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.7 V |
| Required Sensors/Components | Accelerator pedal position sensor |
| Frequency of Operation | Continuous |
| VPA voltage | 0.5 V to 4.5 V |
| VPA2 voltage | 1.2 V to 4.7 V |
| Difference between VPA and VPA2 voltages | more than 0.05 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR POSITION SENSOR) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the values displayed on the tester.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2 |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V | More than 0.02 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 4.7 V |
| *a | Accelerator Pedal |
| *b | Depressed |
| *c | Released |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM) |
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-6 (VPA) - A74-55 (VPA) | Always | Below 1 Ω |
| A36-5 (EPA) - A74-59 (EPA) | Always | Below 1 Ω |
| A36-4 (VCPA) - A74-57 (VCPA) | Always | Below 1 Ω |
| A36-3 (VPA2) - A74-56 (VPA2) | Always | Below 1 Ω |
| A36-2 (EPA2) - A74-60 (EPA2) | Always | Below 1 Ω |
| A36-1 (VCP2) - A74-58 (VCP2) | Always | Below 1 Ω |
| A36-6 (VPA) or A74-55 (VPA) - Body ground | Always | 10 kΩ or higher |
| A36-5 (EPA) or A74-59 (EPA) - Body ground | Always | 10 kΩ or higher |
| A36-4 (VCPA) or A74-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A36-3 (VPA2) or A74-56 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A36-2 (EPA2) or A74-60 (EPA2) - Body ground | Always | 10 kΩ or higher |
| A36-1 (VCP2) or A74-58 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A36-4 (VCPA) - A36-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A36-1 (VCP2) - A36-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Accelerator Pedal Sensor Assembly) |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Fully depress and release the accelerator pedal.
Check that 5 seconds or more have elapsed since the ignition switch was turned to ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||