Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus:

    1. for Main Body ECU: Body / Main Body / Data List.

    2. for Combination Meter: Body / Combination Meter / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Ignition switch ACC signal /
    OFF or ON
    OFF: Ignition switch off
    ON: Ignition switch ACC or ON
    -
    IG SW
    Ignition switch ON signal /
    OFF or ON
    OFF: Ignition switch ACC or off
    ON: Ignition switch ON
    -
    Dimmer SW*1
    Dimmer switch high signal /
    OFF or ON
    OFF: Dimmer switch in low position
    ON: Dimmer switch in high or high flash position
    -
    Passing Light SW*1
    Dimmer switch high flash signal /
    OFF or ON
    OFF: Dimmer switch not in high flash position
    ON: Dimmer switch in high flash position
    -
    Rear Fog Light SW
    Not available /
    OFF or ON
    -
    -
    Front Fog Light SW*1*2
    Fog light switch signal /
    OFF or ON
    OFF: Fog light switch off
    ON: Fog light switch on
    -
    Auto Light SW*1
    Light control switch AUTO signal /
    OFF or ON
    OFF: Light control switch not in AUTO position
    ON: Light control switch in AUTO position
    -
    Head Light SW (Head)*1
    Light control switch HEAD signal /
    OFF or ON
    OFF: Light control switch not in HEAD position
    ON: Light control switch in HEAD position
    -
    Head Light SW (Tail)*1
    Light control switch TAIL signal /
    OFF or ON
    OFF: Light control switch not in TAIL and HEAD position
    ON: Light control switch in TAIL or HEAD position
    -
    Illumination Rate Info*1
    Illumination rate information/
    0 to 2162.65 ms
    Value output according to ambient light levels
    -
    Response Time
    Delay timing of lighting the taillights when the automatic light control sensor detects brightness change /
    Normal or Long
    Customized setting displayed
    -
    Sensitivity*1
    Sensitivity of the automatic light control system /
    Normal, Dark2, Dark1, Light1 or Light2
    Customized setting displayed
    -
    Disp Ex ON Sen*1
    Ambient brightness level required to dim display lights /
    Normal, Dark2, Dark1, Light1 or Light2
    Customized setting displayed
    -
    Disp Ex OFF Sen*1
    Ambient brightness level required to cancel dimming display lights /
    Normal, Dark2, Dark1, Light1 or Light2
    Customized setting displayed
    -
    The Number of DTC
    Number of DTCs /
    0 to 255
    Number of DTCs displayed
    -

    1. *1: w/ Automatic Light Control System
    2. *2: w/ Fog Light

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Signal Switch (Right)
    Turn signal switch signal (turn right) /
    OFF or ON
    OFF: Turn signal switch right off (turn right)
    ON: Turn signal switch right on (turn right)
    -
    Turn Signal Switch (Left)
    Turn signal switch signal (turn left) /
    OFF or ON
    OFF: Turn signal switch left off (turn left)
    ON: Turn signal switch left on (turn left)
    -
    Hazard Flasher Switch
    Hazard warning signal switch /
    OFF or ON
    OFF: Hazard warning signal switch off
    ON: Hazard warning signal switch on
    -


ACTIVE TEST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Taillight Relay*1
    Taillight relay
    OFF or ON
    -
    Headlight Relay*1
    Headlight relay
    OFF or ON
    -
    Head Light Hi*1
    Headlight dimmer relay
    OFF or ON
    Light control switch is in HEAD position
    Front Fog Light Relay*1*2
    Front fog light relay
    OFF or ON
    Light control switch is in TAIL or HEAD position
    Rear Fog Light Relay
    Not available
    OFF or ON
    -

    1. *1: w/ Automatic Light Control System
    2. *2: w/ Fog Light