Home › Drivetrain ยท C54 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE

TRANSMISSION CONTROL CABLE > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Install the transmission control cable assembly with the 3 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    C235168E01
  1. Install the control select cable and the control shift cable to the control cable bracket the 2 new clips B.
    Text in Illustration 
    *1
    Control Shift Cable
    *2
    Control Select Cable
    *3
    Clip A
    *4
    Clip B

  1. Install the control select cable and the control shift cable to manual transaxle assembly with the 2 clips A and 2 washers.



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C195134E01
  1. Rotate the transmission control cable nut counterclockwise 180° and push in the lock while holding the nut.
    Text in Illustration 
    *1
    Nut
    *2
    Lock



    C235548E01
  1. Install the control select cable and the control shift cable to the shift lever plate.
    Text in Illustration 
    *1
    Control Select Cable
    *2
    Control Shift Cable
    *3
    Clip A
    *4
    Clip B
    *5
    Nut
    *6
    Shift Lever Plate

    NOTICE:
    After installation, check that the cable outer lock extends past the line A-A, as shown in the diagram.

  1. Connect the control shift cable to the floor shift shift lever assembly with the clip B.

  1. Connect the control select cable to the floor shift shift lever assembly with the clip A.

    NOTICE:
    Install the cable end adjustment mechanism so that the lock faces the driver seat.



3. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY


    C235560E01
  1. Remove the clip and disconnect the control select cable from the floor shift shift lever assembly.
    Text in Illustration 
    *1
    Control Select Cable



    C235815E01
  1. Slide the adjuster case cover in the direction shown in the illustration.
    Text in Illustration 
    *1
    Adjuster Case Cover



    C241538E01
  1. Pull out the lock piece from the adjuster case.
    Text in Illustration 
    *1
    Lock Piece
    *2
    Adjuster Case
    *3
    Cable Rod

  1. Install the control select cable to the floor shift shift lever assembly with the clip.

    NOTICE:
    1. Make sure to adjust the length at the neutral shift position.
    2. Make sure that the lock piece is protruding from the adjuster case.

  1. Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.

  1. Press the lock piece into the adjuster case and lock it.



    C235819E01
  1. Slide the adjuster case cover in the direction shown in the illustration.
    Text in Illustration 
    *1
    Adjuster Case Cover

    NOTICE:
    Slide the cover past the protrusion portion of the lock piece.



4. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
  1. Install the front No. 1 floor heat insulator with the 2 bolts and nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



5. INSTALL EXHAUST PIPE GASKET


    A128852E04
  1. Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.
    Text in Illustration 
    *1
    Exhaust pipe gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Exhaust Manifold

    NOTICE:
    1. Install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket by dropping it, etc.
    4. Do not damage the outer surface of the gasket.
    5. Do not push in the gasket with the exhaust pipe when connecting it.



6. INSTALL NO. 2 EXHAUST PIPE GASKET


A128852E04
  1. Using a plastic hammer and a wooden block, tap in a new No. 2 exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
    Text in Illustration 
    *1
    No. 2 Exhaust Pipe Gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Front Exhaust Pipe Assembly

    NOTICE:
    1. Install the gasket in the correct direction.
    1. Do not reuse the gasket.
    1. Do not damage the gasket by dropping it, etc.
    1. Do not damage the outer surface of the gasket.
    1. Do not push in the gasket with the exhaust pipe when connecting it.



7. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A128853
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum Length:
    41.5 mm (1.634 in.)

    If the length is not as specified, replace the compression spring.

  1. Hang the front exhaust pipe assembly with the 3 exhaust pipe supports.



    A247549J01
  1. Install the front exhaust pipe sub-assembly onto the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Front Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 8.5 mm (0.335 in.)

    HINT:
    After the installation, check that the gaps between the flanges of the exhaust manifold converter subassembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



    A128853
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum Length:
    38.5 mm (1.516 in.)

    HINT:
    If the length is not as specified, replace the compression spring.



    A247551J01
  1. Connect the tail exhaust pipe assembly onto the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Text in Illustration 
    *1
    Front Exhaust Pipe Assembly
    *2
    Tail Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 6.5 mm (0.256 in.)

    HINT:
    After the installation, check that the gaps between the flanges of the exhaust manifold converter subassembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

  1. Pass the connector through the hole into the inside of the vehicle and install the oxygen sensor wire grommet.

  1. Install the grommet and connect the oxygen sensor connector.



8. INSTALL FRONT FLOOR CENTER BRACE (w/ Side Mudguard)
  1. Install the front floor center brace onto the body with the 2 bolts.

    Torque:
    30 N*m{ 307 kgf*cm , 22 ft.*lbf }



9. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
  1. Install the air cleaner cap sub-assembly with No. 1 air cleaner hose to the throttle body assembly with the 2 clamps.

  1. Tighten the hose clamp.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Engage the wire harness clamp and install the wire harness to the vacuum switching valve assembly.

  1. Connect the vacuum switching valve assembly connector.

  1. Connect the mass air flow meter connector.

  1. Engage the 2 clamps and connect the wire harness to the air cleaner cap sub-assembly and vacuum switching valve assembly.

  1. Connect the No. 2 fuel vapor feed hose to the intake manifold.

  1. Install the fuel vapor feed hose to the No. 1 air cleaner hose.

  1. Connect the fuel vapor feed hose assembly to the vacuum switching valve assembly and No. 1 air cleaner hose.



10. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)


11. INSPECT FOR EXHAUST GAS LEAK