Home › Drivetrain ยท C54 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE

TRANSMISSION CONTROL CABLE > REMOVAL

for Preparation Click here



1. REMOVE REAR CONSOLE BOX ASSEMBLY
(Click here)


2. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE


    A249575
  1. Disconnect the fuel vapor feed hose from the vacuum switching valve assembly and air cleaner hose.

  1. Loosen the 2 hose clamps and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose and vacuum switching valve assembly.



    A249576
  1. Disconnect the No. 2 fuel vapor feed hose from the intake manifold.



    A249577
  1. Disengage the 2 clamps and disconnect the wire harness from the air cleaner cap sub-assembly and vacuum switching valve assembly.

  1. Disconnect the mass air flow meter connector.

  1. Disconnect the vacuum switching valve connector.



    A249578
  1. Loosen the hose clamp and disconnect the No. 1 air cleaner hose from the throttle with motor body assembly.

  1. Disengage the 2 clamps and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.



3. REMOVE FRONT FLOOR CENTER BRACE (w/ Side Mudguard)


A259843
  1. Remove the 2 bolts and the front floor center brace from the body.



4. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A250069
  1. Peel back the floor carpet.



    A250070
  1. Disconnect the heated oxygen sensor connector.

  1. Remove the oxygen sensor wire grommet and pass the connector through the hole to the outside of the vehicle.



    A247548
  1. Remove the 2 bolts and 2 compression springs from the exhaust manifold.



    A247550
  1. Remove the 2 bolts and 2 compression springs from the tail exhaust pipe assembly.

  1. Remove the 3 exhaust pipe supports and the front exhaust pipe assembly.



5. REMOVE EXHAUST PIPE GASKET
  1. Remove the exhaust pipe gasket from the exhaust manifold.



6. REMOVE NO. 2 EXHAUST PIPE GASKET


A128852E04
  1. Using a plastic hammer and a wooden block, tap in a new No. 2 exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
    Text in Illustration 
    *1
    No. 2 Exhaust Pipe Gasket
    *2
    Wooden Block
    *3
    Plastic Hammer
    *4
    Front Exhaust Pipe Assembly

    NOTICE:
    1. Install the gasket in the correct direction.
    1. Do not reuse the gasket.
    1. Do not damage the gasket by dropping it, etc.
    1. Do not damage the outer surface of the gasket.
    1. Do not push in the gasket with the exhaust pipe when connecting it.



7. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR


C235165
  1. Remove the 2 bolts, nut and the front No. 1 floor heat insulator.



8. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C235167E03
  1. Remove the clip A, and disconnect the control select cable from the floor shift shift lever assembly.
    Text in Illustration 
    *1
    Control Select Cable
    *2
    Control Shift Cable
    *3
    Clip A
    *4
    Clip B
    *5
    Nut
    *6
    Shift Lever Plate
    *a
    Rotate 180°

  1. Disengage the clip B, and disconnect the control shift cable from the floor shift shift lever assembly.

  1. Rotate the nut clockwise approximately 180° and, while holding the nut in that position, separate the control select cable from the shift lever plate.

    NOTICE:
    Do not rotate the nut excessively as it may damage the internal spring and the transmission control cable assembly will not be reusable.

  1. Rotate the nut clockwise approximately 180° and, while holding the nut in that position, separate the control shift cable from the shift lever plate.

    NOTICE:
    Do not rotate the nut excessively as it may damage the internal spring and the transmission control cable assembly will not be reusable.



9. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    C235168E01
  1. Remove the clip A and washer, and separate the control shift cable from the manual transaxle assembly.
    Text in Illustration 
    *1
    Control Shift Cable
    *2
    Control Select Cable
    *3
    Clip A
    *4
    Clip B

  1. Remove the clip B from the control shift cable, and separate the control shift cable from the control cable bracket.

  1. Remove the clip A and washer, and separate the control select cable from the manual transaxle assembly.

  1. Remove the clip B from the control select cable, and separate the control select cable from the control cable bracket.



    C106362
  1. Remove the 3 nuts and the transmission control cable assembly.