Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

1NZ-FE SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in P or neutral the A/C switch should be off and all accessory switches should be off.

  1. Warm up the engine.

  2. Turn the A/C switch off.

  3. Turn the ignition switch off.

  4. Connect the intelligent tester to the DLC3.

  5. Turn the ignition switch to ON.

  6. Turn the tester on.

  7. Enter the following menus: Powertrain / Engine and ECT / Data List.

    HINT:
    1. To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
    2. When you select a measurement group, the ECU data belonging to that group is displayed.
    3. Measurement Group List / Description
      1. All Data / All data
      2. Primary / -
      3. Engine Control / Engine control system related data
      4. Ptrl General / -
      5. Ptrl AF Control / Air-fuel ratio control system related data
      6. Ptrl AF O2 Sensor / Air-fuel ratio sensor and heated oxygen sensor related data
      7. Ptrl Throttle / Gasoline throttle system related data
      8. Ptrl Intake Control / Intake control system related data
      9. Ptrl Valve Control / Valve control system related data
      10. Ptrl Misfire / "Misfire" related data
      11. Ptrl Starting / "Difficult to start" related data
      12. Ptrl Rough Idle / "Rough idle" related data
      13. Ptrl Evaporative / Evaporative system related data
      14. Ptrl CAT Converter / Catalytic converter related data
      15. Check Mode / Check mode related data
      16. Monitor Status / Monitor status related data
      17. Ignition / Ignition system related data
      18. Charging Control / Charging control system related data
      19. Compression / Data used during "Check the Cylinder Compression" Active Test
      20. AT / Automatic transaxle system related data
      21. Vehicle Information / Vehicle information

  8. According to the display on the tester, read the Data List.

    HINT:
    1. The title used for each group of Data List items in this repair manual does not appear on the intelligent tester. However, the name in parentheses after the title, which is a Measurement Group, does appear on the tester. When the name shown in parentheses is selected on the tester, all the Data List items listed for that group will be displayed.
    2. "Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.


Various Vehicle Conditions 1 (All Data)

Vehicle Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
Yes
Diagnostic Note:
  1. This is the current vehicle speed
  2. The vehicle speed is detected using the wheel speed sensors.
    1. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

Engine Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
650 to 750 rpm: Idling (AT)
600 to 700 rpm: Idling (MT)
Yes
Results of real-vehicle check:
Idling (warm up the engine, A/C off): 704 rpm (for Automatic Transaxle)
Diagnostic Note:
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.

Calculate Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Calculate Load
Load calculated by ECM/
Min.: 0%, Max.: 100%
-
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 0.0%
  2. Idling (warm up the engine): 30.5%
  3. Running without load (3000 rpm): 21.9%
Diagnostic Note:
This is the engine load calculated based on the estimated intake manifold pressure.
Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%)
(For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)

Vehicle Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
-
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 0.0%
  2. Idling (warm up the engine): 20.3%
  3. Running without load (3000 rpm): 16.8%
Diagnostic Note:
This is the engine intake air charging efficiency.
Vehicle Load = Current intake airflow (g/rev.) / maximum intake airflow
Maximum intake airflow = Displacement (L) / 2 x 1.2 (g/rev.)

HINT:
Due to individual engine differences, intake air temperature, etc., the value may exceed 100%.
Intake airflow (g/rev.) = Intake airflow (gm/sec) x 60 / Engine speed (rpm)
(Intake airflow (gm/sec) is MAF)


MAF 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MAF
Airflow rate from Mass Air Flow (MAF) meter/
Min.: 0 gm/sec, Max.: 655.35 gm/sec
1.0 to 3.0 gm/sec: Idling
3.0 to 7.0 gm/sec: 2500 rpm (without load)
4.0 to 8.0 gm/sec: 3000 rpm (without load)
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 0.20 gm/sec
  2. Idling (warm up the engine): 1.84 gm/sec
  3. Running without load (2500 rpm): 5.68 gm/sec
  4. Running without load (3000 rpm): 6.59 gm/sec
Diagnostic Note:
This is the intake air amount from the mass air flow meter.

Atmosphere Pressure 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa (0 mmhg), Max.: 255 kPa (1912 mmhg)
Equivalent to the atmosphere pressure (absolute pressure)
Yes
Results of real-vehicle check:
Idling (warm up the engine): 103 kPa
Diagnostic Note:
  1. This value is calculated from the intake air amount.
  2. Standard atmospheric pressure: 101 kPa
  3. For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather.

Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Coolant Temp
Coolant temperature/
Min.: -40°C, Max.: 140°C
80 to 100°C (176 to 212°F): After warming up
Yes
Diagnostic Note:
This is the engine coolant temperature.

HINT:
  1. After warming up the engine, the engine coolant temperature is 80 to 100°C (176 to 212°F).
  2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
  3. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.


Intake Air 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to temperature at location of mass air flow meter
Yes
Diagnostic Note:
  1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
  2. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

Ambient Temperature 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ambient Temperature
Ambient temperature/
Min.: -40°C, Max.: 215°C
Equivalent to ambient air temperature
Yes

Engine Run Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Yes
Diagnostic Note:
This is the time elapsed since the engine started.

HINT:
The time is counted only while the engine is running.


Initial Engine Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
-
Yes
Diagnostic Note:
This is the coolant temperature stored when the ignition switch is turned to ON.

Initial Intake Air Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
-
Yes
Diagnostic Note:
This is the intake air temperature stored when the ignition switch is turned to ON.

Battery Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
Yes
Results of real-vehicle check:
  1. Ignition switch ON: 12.089 V
  2. Cranking: 11.015 V
  3. Idling (warm up the engine): 13.398 V
Diagnostic Note:
If 11 V or less, characteristics of some electrical components may change.

Throttle Control 1 (Ptrl Throttle)

Accelerator Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accelerator Position
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0.0%
  2. Ignition switch ON (accelerator pedal fully depressed): 100.0%
Diagnostic Note:
This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%.

Accel Sens. No.1 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sens. No.1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1/
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal released
52 to 90%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 16.0%
  2. Ignition switch ON (accelerator pedal fully depressed): 69.4%
Diagnostic Note:
The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.

HINT:
If there are no accelerator pedal position sensor DTCs stored, it is possible to conclude that the accelerator pedal position sensor system is normal.


Accel Sens. No.2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sens. No.2 Volt %
Absolute APP No. 2/
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal released
68 to 100%: Accelerator pedal fully depressed
Yes
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 31.7%
  2. Ignition switch ON (accelerator pedal fully depressed): 85.0%
Diagnostic Note:
The accelerator pedal position sensor No. 2 output is converted using 5 V = 100%.

Throttle Control 2 (All Data)

Accel Sensor Out No.1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sensor Out No.1
APP sensor No. 1 voltage/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0.800 V
  2. Ignition switch ON (accelerator pedal fully depressed): 3.457 V
Diagnostic Note:
This is the raw voltage from the accelerator pedal position sensor No. 1.

Accel Sensor Out No.2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Sensor Out No.2
APP sensor No. 2 voltage/
Min.: 0 V, Max.: 4.98 V
1.2 to 2.0 V: Accelerator pedal released
3.4 to 4.7 V: Accelerator pedal fully depressed
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 1.582 V
  2. Ignition switch ON (accelerator pedal fully depressed): 4.238 V
Diagnostic Note:
  1. This is the raw voltage from the accelerator pedal position sensor No. 2.
  2. Accelerator pedal position sensor No. 2 is used to monitor accelerator pedal position sensor No. 1. When there is a malfunction in sensor No. 1, the ECM uses sensor No. 2 to control the engine.

Throttle Control 3 (Ptrl Throttle)

Accelerator Idle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting released accelerator pedal/
ON or OFF
ON: Accelerator pedal released
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): ON
  2. Ignition switch ON (accelerator pedal fully depressed): OFF
Diagnostic Note:
This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position.

Accel Fully Close Learn #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Fully Close Learn #1
Accelerator fully released learned value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
No
Results of real-vehicle check:
Ignition switch ON: 20.0 deg
Diagnostic Note:
This is the value of accelerator pedal position sensor No. 1 learned when the accelerator pedal is released.

Accel Fully Close Learn #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Accel Fully Close Learn #2
Accelerator fully released learned value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
No
Results of real-vehicle check:
Ignition switch ON: 39.5 deg
Diagnostic Note:
This is the value of accelerator pedal position sensor No. 2 learned when the accelerator pedal is released.

Throttle Sensor Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor Volt %
Absolute throttle position sensor/
Min.: 0%, Max.: 100%
  1. 10 to 22%: Throttle fully closed
  2. 64 to 96%: Throttle fully open
Yes
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 18.8%
  2. Ignition switch ON (accelerator pedal fully depressed): 81.1%
  3. Idling (warm up the engine): 15.2%
  4. Running without load (3000 rpm): 19.2%
Diagnostic Note:
The throttle position sensor No. 1 output is converted using 5 V = 100%.

HINT:
If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.


Throttl Sensor #2 Volt % 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttl Sensor #2 Volt %
Throttle sensor position #2/
Min.: 0%, Max.: 100%
  1. 42 to 62%: Throttle fully closed
  2. 92 to 100%: Throttle fully open
Yes
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 50.9%
  2. Ignition switch ON (accelerator pedal fully depressed): 99.6%
  3. Idling (warm up the engine): 46.6%
Diagnostic Note:
The throttle position sensor No. 2 output is converted using 5 V = 100%.

ST1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
No
Diagnostic Note:
This is the brake pedal switch signal (ST1 - terminal signal).

System Guard 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
System Guard
System guard/
ON or OFF
ON
No
Results of real-vehicle check:
Idling (warm up the engine): ON
Diagnostic Note:
When there is a difference between the target and actual throttle valve opening angles, system guard turns off and stops the electronic throttle control system function.
OFF: Electronic throttle control is stopped.

Open Side Malfunction 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Open Side Malfunction
Open malfunction/
ON or OFF
OFF
No
Diagnostic Note:
This parameter indicates a malfunction in the electronic throttle when the throttle valve is open.

Throttle Idle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
-
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): ON
  2. Ignition switch ON (accelerator pedal fully depressed): OFF
  3. Idling (warm up the engine): ON
  4. Running without load (3000 rpm): OFF
Diagnostic Note:
This is a parameter calculated by the ECM.
The value is ON when the throttle is at the idle position and OFF when the throttle is open.

Throttle Require Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 4.98 V
-
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0.917 V
  2. Ignition switch ON (accelerator pedal fully depressed): 4.042 V
  3. Idling (warm up the engine): 0.761 V
Diagnostic Note:
This is a value calculated by the ECM showing the voltage for the target throttle valve position. It is almost an exact match of the Throttle Position No. 1 value except during very rapid throttle valve movement, such as that used during wheelspin control.

Throttle Sensor Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sensor Position
Throttle sensor position/
Min.: 0%, Max.: 100%
  1. 0%: Throttle fully closed
  2. 50 to 80%: Throttle fully open
Yes
Results of real-vehicle check:
Idling (warm up the engine): 0.0%
Diagnostic Note:
This is the throttle valve opening amount used for engine control.
(100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idling speed during idling.)
This value has no meaning when the ignition switch is ON and the engine is stopped.
The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%.

Throttle Position No. 1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position No. 1
Throttle position sensor No. 1 output voltage/
Min.: 0 V, Max.: 4.98 V
Almost same as "Throttle Require Position"
  1. 0.5 to 1.1 V: Throttle fully closed
  2. 3.2 to 4.8 V: Throttle fully open
  3. 0.6 to 1.4 V: Fail-safe operating
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0.937 V
  2. Ignition switch ON (accelerator pedal fully depressed): 4.042 V
  3. Idling (warm up the engine): 0.761 V
Diagnostic Note:
This is the throttle position sensor No. 1 output voltage.

Throttle Position No. 2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position No. 2
Throttle position sensor No. 2 output voltage/
Min.: 0 V, Max.: 4.98 V
  1. 2.1 to 3.1 V: Throttle fully closed
  2. 4.6 to 5.0 V: Throttle fully open
  3. 2.1 to 3.1 V: Fail-safe operating
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 2.539 V
  2. Ignition switch ON (accelerator pedal fully depressed): 4.960 V
  3. Idling (warm up the engine): 2.324 V
Diagnostic Note:
This is the throttle position sensor No. 2 output voltage.

Throttle Position Command 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
-
No
Diagnostic Note:
Throttle Position Command is the same value as Throttle Require Position.

Throttle Sens Open Pos #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sens Open Pos #1
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V
No
Results of real-vehicle check:
Ignition switch ON: 0.917 V
Diagnostic Note:
This is the throttle position sensor No. 1 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch on.

Throttle Sens Open Pos #2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Sens Open Pos #2
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V
No
Results of real-vehicle check:
Ignition switch ON: 2.031 V
Diagnostic Note:
This is the throttle position sensor No. 2 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch on.

Throttle Motor Current 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0.0 A
  2. Ignition switch ON (accelerator pedal fully depressed): 0.9 A
  3. Idling (warm up the engine): 0.9 A
  4. Running without load (3000 rpm): 0.5 A
Diagnostic Note:
  1. When this value is large but the actual opening angle (Throttle Position No. 1) does not reach the target opening angle (Throttle Require Position), there is an unable to open malfunction.
  2. This value normally fluctuates around 1 A.

Throttle Motor DUTY 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor DUTY
Throttle actuator/
Min.: 0%, Max.: 100%
0.5 to 40%: Idling after engine warmed up.
Yes
Diagnostic Note:
This is the output duty ratio of the throttle actuator drive circuit.

Throttle Motor Duty (Open) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Duty (Open)
Throttle actuator duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0%
  2. Ignition switch ON (accelerator pedal fully depressed): 17%
  3. Idling (warm up the engine): 0%
  4. Running without load (3000 rpm): 9%
Diagnostic Note:
  1. This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal.
  2. When the throttle valve is being opened, Throttle Motor Duty (Open) is 10 to 50%.

Throttle Motor Duty (Close) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Motor Duty (Close)
Throttle actuator duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
No
Results of real-vehicle check:
  1. Ignition switch ON (accelerator pedal released): 0%
  2. Ignition switch ON (accelerator pedal fully depressed): 0%
  3. Idling (warm up the engine): 11%
  4. Running without load (3000 rpm): 0%
Diagnostic Note:
This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.

HINT:
During idling, the throttle valve opening angle is usually controlled using a duty ratio drive signal which closes the throttle valve. However, when carbon deposits build up, it may be necessary to open the throttle valve more than the throttle valve opener does. In that case, the opening angle is controlled using a "Throttle Motor Duty (Open)" signal which opens the throttle valve.


Throttle Fully Close Learn 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Fully Close Learn
Throttle valve fully closed (learned value)/
Min.: 0 V, Max.: 4.980 V
0.4 to 1.0 V: Accelerator pedal released
No
Results of real-vehicle check:
Ignition switch ON: 0.683 V
Diagnostic Note:
  1. The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle (approximately 4 to 7°, the position when the ignition switch is ON, the accelerator pedal is released and the throttle actuator is off).
  2. Learning is performed immediately after the ignition switch is turned to ON.

+BM Voltage 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
+BM Voltage
+BM voltage/
Min.: 0 V, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal
No
Diagnostic Note:
This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off).

Actuator Power Supply 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Actuator Power Supply
Actuator power supply/
ON or OFF
ON: Idling
No
Diagnostic Note:
If +BM power is lost, this item changes to OFF.

Throttle Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Throttle Position
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 0.00 deg
Diagnostic Note:
This value has no meaning when the ignition switch is ON and the engine is stopped.

Idle Speed Control (Ptrl Rough Idle)

ISC Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Flow
Flow rate calculated using information from MAF (mass air flow meter)/
Min.: 0 L/s, Max.: 79.99 L/s
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 1.38 L/s
Diagnostic Note:
This is the total ISC airflow amount (the amount of intake air necessary to maintain idling).

HINT:
ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


ISC Position 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Position
Requested throttle opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 1.76 deg
Diagnostic Note:
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).

ISC Feedback Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Feedback Value
ISC feedback amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): -0.03 L/s
Diagnostic Note:
This is the feedback amount necessary to adjust the airflow amount to maintain the target idling speed.

HINT:
When the idling speed differs from the target, the feedback amount is adjusted. If the feedback amount becomes more than a certain value, this will be reflected in the ISC learned airflow value.


ISC Learning Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
ISC Learning Value
ISC learned airflow value/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 1.35 L/s
Diagnostic Note:
This is the learned value of the airflow amount necessary for engine idling.

HINT:
  1. If ISC Feedback Value becomes more than a certain value, this will be reflected in ISC Learning Value.
  2. ISC Flow (total ISC airflow amount) = ISC Learning Value + ISC Feedback Value + each compensation amount


Electric Load Feedback Val 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Load Feedback Val
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Diagnostic Note:
This is the ISC compensation amount determined according to the electrical load.

Air Conditioner FB Val 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Air Conditioner FB Val
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Diagnostic Note:
This is the ISC compensation amount determined according to the air conditioner load.

Low Revolution Control 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Low Revolution Control
Low engine speed control operation state/
ON or OFF
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): OFF
Diagnostic Note:
  1. This parameter indicates whether the engine speed dropped immediately after starting due to poor combustion, etc. This parameter changes to ON when the engine speed drops to below the following speeds 1 to 7 seconds after the engine is started (when the A/C is on, the engine speed thresholds below increase by 100 to 200 rpm).
    1. 900 rpm (when the engine coolant temperature is 10°C (50°F)
    1. 850 rpm (when the engine coolant temperature is 30°C (86°F)
    1. 750 rpm (when the engine coolant temperature is 60°C (140°F)
      Before 5 seconds elapse after starting the engine, this parameter indicates the status of the previous trip.
      After 5 seconds elapse after starting the engine, this parameter indicates the status of the current trip.

      HINT:
      The engine is considered to have started when the engine speed reaches 400 rpm. When the engine speed decreases immediately after starting the engine, this parameter changes to ON and remains ON for the rest of the trip.
      ON: The engine speed decreased immediately after starting the engine.
      OFF: The engine speed did not decrease immediately after starting the engine.

  2. For use when engine stall, starting problems or rough idle is present.

N Range Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
N Range Status
Shift lever N status/
ON or OFF
-
Yes
Diagnostic Note:
This item is displayed only for Automatic Transaxle.

Eng Stall Control FB Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Eng Stall Control FB Flow
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 0.00 L/s
Diagnostic Note:
  1. The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall.
  2. For use when engine stall, starting problems or rough idle is present.

Fuel System (Ptrl General)

Injector (Port) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injector (Port)
Injection period of the No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
-
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 2541 μs
  2. Running without load (3000 rpm): 2053 μs
Diagnostic Note:
This is the injection period of the No. 1 cylinder (the command value from the ECM).

Injection Volum (Cylinder 1) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Injection Volum (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.15 ml: Idling, engine warmed up
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 0.068 ml
  2. Running without load (3000 rpm): 0.052 ml
Diagnostic Note:
This is the fuel injection volume for 10 injections.

Fuel Pump/Speed Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Pump/Speed Status
Fuel pump status/
ON or OFF
ON: Starter on or engine running
Yes

EVAP System (Ptrl Evaporative)

EVAP (Purge) VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP (Purge) VSV
Purge VSV control duty/
Min.: 0%, Max.: 100%
-
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 0.0%
  2. Running without load (3000 rpm): 65.0%
Diagnostic Note:
  1. This is the command signal from the ECM.
  2. This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed.
    *: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV.
  3. When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV is 0%.

Evap Purge Flow 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Evap Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
-
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 0.0%
  2. Running without load (3000 rpm): 5.4%
Diagnostic Note:
This is the percentage of total engine airflow contributed by EVAP purge operation.
(Evap Purge Flow = Purge flow / Engine airflow x 100 (%))
It is based on MAF and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV.

Purge Density Learn Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Purge Density Learn Value
Purge density learned value/
Min.: -200, Max.: 199.993
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 0.000
Diagnostic Note:
Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air-fuel ratio feedback compensation value) related to a 1% purge flow rate.
When Purge Density Learn Value is a large negative value, the purge effect is large.
The purge density is determined from the change in the air-fuel ratio feedback compensation value when purge flow is introduced.
Purge density learning is performed so that the feedback compensation value is 0 +/-2%.

HINT:
  1. Usually, the value is approximately +/-1%.
  2. 1%: The concentration of HC in the purge gas is relatively low.
  3. 0%: The concentration of HC in the purge gas is approximately equal to the stoichiometric air-fuel ratio.
  4. Large negative values indicate that the concentration of HC in the purge gas is relatively high.


EVAP Purge VSV 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
Yes
Diagnostic Note:
This parameter displays ON when EVAP (Purge) VSV is 30% or more, and displays OFF when the VSV duty ratio is less than 30%.

Air Fuel Ratio Control 1 (All Data)

Target Air-Fuel Ratio 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Target Air-Fuel Ratio
Target air-fuel ratio/
Min.: 0, Max.: 1.999
0.8 to 1.2: Idling
Yes
Diagnostic Note:
This is the target air-fuel ratio used by the ECM.
  1. 1.0 is the stoichiometric air-fuel ratio. Values that are more than 1 indicate the system attempting to make the air-fuel ratio leaner. Values that are less than 1 indicate the system attempting to make the air-fuel ratio richer.

Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)

O2S B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2S B1S1
Heated oxygen sensor output voltage for sensor 1/
Min.: 0 V, Max.: 1.275 V
0 to 1 V:
Driving at 70 km/h (43 mph)
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 0.055 V
  2. Running without load (3000 rpm): 0.800 V
Diagnostic Note:
This is the output voltage of the heated oxygen sensor (sensor 1).
  1. Values close to 0 V indicate an air-fuel ratio leaner than the stoichiometric ratio.
  2. Values close to 1 V indicate an air-fuel ratio richer than the stoichiometric ratio.
  3. During air-fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V.
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor.

O2S B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2S B1S2
Heated oxygen sensor output voltage for sensor 2/
Min.: 0 V, Max.: 1.275 V
0 to 1 V:
Driving at 70 km/h (43 mph)
Yes
  1. Idling (warm up the engine): 0.720 V
  2. Running without load (3000 rpm): 0.330 V
Diagnostic Note:
This is the output voltage of the heated oxygen sensor (sensor 2).
  1. Values close to 0 V indicate an air-fuel ratio leaner than the stoichiometric ratio.
  2. Values close to 1 V indicate an air-fuel ratio richer than the stoichiometric ratio.
  3. During air-fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V.
Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor.

O2 LR Switch Time B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2 LR Switch Time B1S1
Heated oxygen sensor voltage Lean to Rich switching time for sensor 1/
Min.: 0 ms, Max.: 16711.68 ms
Within 1000 ms
Yes

O2 RL Switch Time B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2 RL Switch Time B1S1
Heated oxygen sensor voltage Rich to Lean switching time for sensor 1/
Min.: 0 ms, Max.: 16711.68 ms
Within 1000 ms
Yes

Short FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Short FT #1
Short-term fuel trim/
Min.: -100%, Max.: 99.2%
-15 to 15%
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): -3.125%
  2. Running without load (3000 rpm): 0.781%
Diagnostic Note:
This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the heated oxygen sensor bank 1 sensor 1 for feedback.
It is possible to check this value for each bank.

Long FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Long FT #1
Long-term fuel trim/
Min.: -100%, Max.: 99.2%
-15 to 15%
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): -3.907%
  2. Running without load (3000 rpm): -5.469%
Diagnostic Note:
The ECM will learn the Long FT values based on Short FT. The goal is to keep Short FT at 0% to keep the A/F mixture at the stoichiometric ratio.
This value is used to determine whether the system related to air-fuel ratio control is malfunctioning.
The condition of the system is determined based on the sum of Short FT and Long FT (excluding times when the system is in transition).
  1. +15% or more: There may be a lean air-fuel ratio.
  2. -15 to +15%: The air-fuel ratio can be determined to be normal.
  3. -15% or less: There may be a rich air-fuel ratio.
  4. The learned value is cleared when the battery cable is disconnected.
  5. Air-fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range.
    "A/F Learn Value Idle #1", "A/F Learn Value Low #1", "A/F Learn Value Mid1 #1", "A/F Learn Value Mid2 #1" and "A/F Learn Value High #1" indicate the learned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.

A/F Learn Value Idle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Idle #1
Air-Fuel Learn Value of idle area/
Min.: -50%, Max.: 49.6%
-15% to +15%
Yes
Diagnostic Note:
Learning is performed when idling with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher).

A/F Learn Value Low #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Low #1
Air-Fuel Learn Value of low load area/
Min.: -50%, Max.: 49.6%
-15% to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value Mid1 #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Mid1 #1
Air-Fuel Learn Value of middle 1 load area/
Min.: -50%, Max.: 49.6%
-15% to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts).

A/F Learn Value Mid2 #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value Mid2 #1
Air-Fuel Learn Value of middle 2 load area/
Min.: -50%, Max.: 49.6%
-15% to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts).

A/F Learn Value High #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/F Learn Value High #1
Air-Fuel Learn Value of high load area/
Min.: -50%, Max.: 49.6%
-15% to +15%
Yes
Diagnostic Note:
Learning is performed when driving with the engine warmed up (engine coolant temperature is 80°C [176°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).

Total FT #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Total FT #1
Total fuel trim/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
Yes
Diagnostic Note:
Total FT #1 = Short FT #1 + Long FT #1

Fuel System Status #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel System Status #1
Fuel system status/
OL, CL, OLDrive, OLFault or CLFault
CL: Idling after warming up
Yes
Diagnostic Note:
  1. OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
  2. CL (Closed Loop): Feedback for fuel control.
  3. OL Drive: Open loop due to driving conditions (fuel enrichment).
  4. OL Fault: Open loop due to a detected system fault.
  5. CL Fault: Closed loop but the heated oxygen sensor bank1 sensor1, which is used for fuel control, is malfunctioning.

O2FT B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
O2FT B1S1
Short-term fuel trim associated with sensor 1/
Min.: -100%, Max.: 99.2%.
-15 to 15%
Yes
Diagnostic Note:
Same as Short FT #1

Ignition System (Ignition)

IGN Advance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg.
BTDC 0 to 14 deg.: Idling
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 7.5 deg
  2. Running without load (3000 rpm): 33.0 deg

Knock Feedback Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Knock Feedback Value
Knocking feedback value/
Min.: -1024° CA, Max.: 1023.9° CA
-
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): -1.5° CA
  2. Running without load (3000 rpm): -1.5° CA
Diagnostic Note:
This is the ignition timing retard compensation amount determined by the presence or absence of knocking.
Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount
Example: 21°CA = 10° + 14° - 3°
*1: The most retarded timing value is a constant determined by the engine speed and engine load.
*2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3°CA as possible.
When Knock Feedback Value is less than -4°CA, Knock Correct Learn Value is slowly decreased.
When Knock Feedback Value is more than -2°CA, Knock Correct Learn Value is slowly increased.
*3: The base value is -3°CA and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased.
  1. -1°CA: There is no knocking and ignition timing is advanced.
  2. -6°CA: Knocking is present and the ignition timing is being retarded.

HINT:
If Knock Feedback Value does not change around the time when knocking occurs even though knocking continues (for example, stays at -3°CA), it can be determined that knocking is not being detected.
Possible Causes:
  1. There is a problem with the knock sensor sensitivity.
  2. The knock sensor is improperly installed.
  3. There is a problem with a wire harness.


Knock Correct Learn Value 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Knock Correct Learn Value
Knocking correction learned value/
Min.: -1024° CA, Max.: 1023.9° CA
-
Yes
Results of real-vehicle check:
  1. Idling (warm up the engine): 10.2° CA
  2. Running without load (3000 rpm): 9.0° CA
Diagnostic Note:
Refer to "Knock Feedback Value".
When there is knocking or a lack of power, compare the following values to another vehicle of the same model.
  1. Engine speed
  2. Calculate Load
  3. IGN Advance
  4. Knock Feedback Value
  5. Knock Correct Learn Value
Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced.
Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.

HINT:
When knocking continues even though Knock Correct Learn Value is less than that of the vehicle being used for comparison (in other words, the ignition timing is being retarded but the knocking is not stopping), there may be a buildup of deposits or other such problems due to deterioration over time (oil entering the cylinders, poor quality fuel, etc.).


Idle Spark Advn Ctrl #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Spark Advn Ctrl #1
Idle Spark Advn Ctrl #2
Idle Spark Advn Ctrl #3
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 1 to No.4)/
Min.: 0° CA, Max.: 15.93° CA
-
Yes
Diagnostic Note:
  1. This is the ignition timing advance compensation amount used to stabilize idling (each cylinder has a separate value). When the speed for a certain cylinder drops, the system advances the timing for that particular cylinder in an attempt to restore the speed and stabilize idling.
  2. It may be possible to use this item to help determine specific cylinders which are not operating normally.

VVT Control 1 (All Data)

Actual VVT Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Actual VVT Angle #1
Actual VVT Angle #1/
Min.: 0 DegFR, Max.: 639.99 DegFR
-
Yes
Diagnostic Note:
This item is displayed only for freeze frame data.

VVT Control 2 (Ptrl Valve Control)

VVT Control Status #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Control Status #1
Variable valve Timing (VVT) control status/
ON or OFF
-
Yes
Diagnostic Note:
ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF).
OFF: The system is commanding the timing to change to the most retarded timing.

VVT Advance Fail 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Advance Fail
VVT control failure status/
ON or OFF
ON: When VVT advance fails
Yes
Diagnostic Note:
ON: There is an intake VVT timing advance malfunction.

VVT Aim Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Aim Angle #1
VVT hold duty learned value/
Min.: 0%, Max.: 399.9%
-
No
Diagnostic Note:
This value represents the duty ratio necessary to operate the camshaft timing oil control valve in order to block the camshaft timing oil control valve path and maintain the advanced state of the VVT controller. This is only available during the Active Test.
Refer to "VVT OCV Duty #1".

VVT Change Angle #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT Change Angle #1
VVT displacement angle/
Min.: 0 DegFR, Max.: 639.9 DegFR
-
No
Diagnostic Note:
This is the VVT displacement angle during forced operation.
This is only available during the Active Test.
By checking VVT Change Angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output.
Refer to "VVT OCV Duty #1".

VVT OCV Duty #1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
VVT OCV Duty #1
VVT camshaft timing oil control valve operation duty/
Min.: 0%, Max.: 399.9%
-
No
Diagnostic Note:
This is the requested duty value for forced operation.
This is only available during the Active Test.
Results of the real-vehicle check when performing the Control the VVT Linear (Bank 1) Active Test:
VVT OCV Duty #1 = 0%, VVT Change Angle #1 = 0 DegFR
↓
VVT OCV Duty #1 = 38%, VVT Change Angle #1 = 0 DegFR
↓
VVT OCV Duty #1 = 46%, VVT Change Angle #1 = 0 DegFR
↓
VVT OCV Duty #1 = 54%, VVT Change Angle #1 = 0 DegFR
↓
VVT OCV Duty #1 = 57%, VVT Change Angle #1 = 0.3 DegFR
↓
VVT OCV Duty #1 = 58%, VVT Change Angle #1 = 13.0 DegFR
↓
VVT OCV Duty #1 = 59%, VVT Change Angle #1 = 35.2 DegFR
After the above test, VVT Aim Angle #1 = 37.0%.

Catalyst (Ptrl CAT Converter)

Catalyst Temp B1S1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Catalyst Temp B1S1
Catalyst temperature for sensor 1/
Min.: -40°C, Max.: 6513.5°C
-
Yes
Diagnostic Note:
This is the temperature of the front catalyst estimated by the ECM.
This value is included in the conditions used to detect catalyst deterioration (DTC P0420), etc., and should therefore be used as a reference when recreating malfunction conditions.

Catalyst Temp B1S2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Catalyst Temp B1S2
Catalyst temperature for sensor 2/
Min.: -40°C, Max.: 6513.5°C
-
Yes
Diagnostic Note:
This is the temperature of the rear catalyst estimated by the ECM.

Various Vehicle Conditions 2 (All Data)

Starter Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Signal
Starter signal/
ON or OFF
ON: Starter operating
OFF: Starter not operating
Yes

Power Steering Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Power Steering Signal
Power steering switch signal/ ON or OFF
ON: Power steering operation
Yes

Neutral Position SW Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Neutral Position SW Signal
PNP switch status/
ON or OFF
ON: Shift lever in P or N
Yes
Diagnostic Note:
This item is displayed only for Automatic Transaxle.

Clutch Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Clutch Switch
Clutch switch status/
ON or OFF
ON: Clutch pedal depressed
Yes
Diagnostic Note:
This item is displayed only for vehicle with Manual Transaxle and Cruise Control System.
Clutch switch (upper) signal status for cruise control system

Clutch Start SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Clutch Start SW
Clutch start switch status/
ON or OFF
ON: Clutch pedal depressed
OFF: Clutch start switch released
Yes
Diagnostic Note:
This item is displayed only for Manual Transaxle.
Clutch start switch (lower) signal status for engine cranking

Stop Light Switch 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
Yes

A/C Signal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/C Signal
A/C switch status/
ON or OFF
ON: A/C on
Yes

Closed Throttle Position SW 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
  1. ON: Throttle fully closed
  2. OFF: Throttle open
Yes

Fuel Cut Condition 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Cut Condition
Fuel cut condition/
ON or OFF
ON: Fuel cut operating
Yes

Immobiliser Communication 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Communication
Immobiliser communication/
ON or OFF
ON: Normal
Yes

Check Mode (Check Mode)

Check Mode 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
Check Mode
Check mode/
ON or OFF
ON: Check mode on
Refer to Check Mode Procedure (Click here).
No
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
No
Misfire Test Result
Check mode result for misfire monitor/
Compl or Incmpl
-
-
No
OXS1 Test Result
Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
-
-
No

Test Result (Monitor Status)

Monitor Information 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stored as Freeze Frame Data
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
*
No
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
*
No
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
*
No
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
*
No
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
*
No
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
*
No
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
*
No
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Not Avl or Avail
-
*
No
O2S(A/FS) Monitor
O2S (A/FS) monitor/
Compl or Incmpl
-
*
No
A/C Monitor
A/C monitor/
Not Avl or Avail
-
*
No
A/C Monitor
A/C monitor/
Compl or Incmpl
-
*
No
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
*
No
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
*
No
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
*
No
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
*
No
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
*
No
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
*
No
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
*
No
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
*
No
*:
Avail: The monitor is available on the vehicle.
Not Avl: The monitor is not available on the vehicle.
Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or the battery cable is disconnected.

Various Vehicle Conditions 3 (All Data)

TC Terminal 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TC Terminal
TC terminal status/
ON or OFF
-
Yes

# Codes (Include History) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
0
No
Diagnostic Note:
This is the number of DTCs stored.

MIL 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MIL
MIL status/
ON or OFF
OFF
No

MIL ON Run Distance 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
MIL ON Run Distance
Distance driven with MIL ON/
Min.: 0 km, Max.: 65535 km
-
No
Diagnostic Note:
This is the distance driven after a DTC is stored (MIL turns on).

Running Time from MIL ON 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Running Time from MIL ON
Running time from MIL ON/
Min.: 0 min, Max.: 65535 min
Running time after MIL turned on
No

Time after DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Time after DTC Cleared
Time after DTCs cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs cleared
Yes
Diagnostic Note:
This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted.

Distance from DTC Cleared 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Distance from DTC Cleared
Distance driven after DTCs cleared/
Min.: 0 km, Max.: 65535 km
Distance driven after DTCs cleared
Yes
Diagnostic Note:
This is the distance driven after DTCs were cleared (or after the vehicle left the factory).

Warmup Cycle Cleared DTC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Warmup Cycle Cleared DTC
Warmup cycles after DTCs cleared/
Min.: 0, Max.: 255
-
Yes
Diagnostic Note:
This is the number of warmup cycles after the DTCs were cleared.
This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory).
*: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or more and reaching a temperature of 70°C (158°F) or higher after the engine is started.

Dist Batt Cable Disconnect 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected
Yes

OBD Requirements 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
OBD Requirements
OBD requirement
EOBD (Euro OBD)
No

Number of Emission DTC 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Number of Emission DTC
Emissions-related DTCs
-
No
Diagnostic Note:
This is the number of emissions-related DTCs.

TC and TE1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
TC and TE1
TC and CG (TE1) terminals of DLC3/
ON or OFF
-
Yes

Misfire (Ptrl Misfire)

Ignition Trig. Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ignition Trig. Count
Ignition counter/
Min.: 0, Max.: 65535
0 to 400
Yes
Diagnostic Note:
This is the cumulative number of ignitions.
This counter is incremented by one for each ignition (this stops when misfire monitoring stops). This value is cleared every 200 revolutions.
The misfire rate for each cylinder is calculated by dividing the misfire count for each cylinder by Ignition Trig. Count.
The misfire rate for each cylinder = Cylinder 1 to 4 Misfire Count / Ignition Trig. Count

HINT:
  1. For 4-cylinder engines, the values range from 0 to 400.
  2. For 6-cylinder engines, the values range from 0 to 600.
  3. For 8-cylinder engines, the values range from 0 to 800.


Cylinder #1 Misfire Count to Cylinder #4 Misfire Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
Misfire count of cylinders 1 to 4/
Min.: 0, Max.: 255
0
Yes
Diagnostic Note:
This is the misfire count for each individual cylinder.
This counter is incremented by one for each misfire and is cleared every 200 revolutions.
Check this item to help determine the malfunctioning cylinder.

All Cylinders Misfire Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
All Cylinders Misfire Count
Misfire count of all cylinders/
Min.: 0, Max.: 255
0
Yes
Diagnostic Note:
This is the total misfire count of all cylinders.
This counter is incremented by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions.

Misfire RPM 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Misfire RPM
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: 0 misfires
Yes
Diagnostic Note:
  1. This is the average engine speed recorded when misfiring occurs.
  2. This value is closer to the actual conditions of the vehicle at the time the misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.

Misfire Load 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Misfire Load
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: 0 misfires
Yes
Diagnostic Note:
  1. This is the average engine load recorded when misfiring occurs.
  2. This value is closer to the actual conditions of the vehicle at the time the misfire occurred than the values of engine speed and engine load stored in the freeze frame data. When reproducing malfunction conditions, use this value as a reference.

HINT:
To convert g/rev to gm/s: RPM / 60 x g/rev = gm/s.


Misfire Margin 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Misfire Margin
Misfire monitoring/
Min.: -128%, Max.: 127%
0 to 99.22%
Yes
Diagnostic Note:
This is the misfire detection margin.
Misfire Margin = (Misfire detection threshold - maximum engine speed variation) / misfire detection threshold x 100%
When the variation in the engine speed is large and exceeds the misfire detection threshold, the misfire count starts. Misfire margin is a measure of how much the engine speed variation can increase with respect to the threshold before the engine is determined to be misfiring.
A large value means there is a large margin for the engine speed to vary before the engine is determined to be misfiring.
Example:
When the engine is not determined to be misfiring, Misfire Margin = 52%.
When the engine is determined to be misfiring, Misfire Margin = -128 to 0%.

Various Vehicle Conditions 4 (All Data)

Engine Speed (Starter Off) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed (Starter Off)
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
-
Yes
Results of real-vehicle check:
Idling (warm up the engine): 1630 rpm
Diagnostic Note:
This is the engine speed immediately after starting the engine.

Starter Count 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Starter Count
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
-
Yes
Diagnostic Note:
This is the number of times the starter turned on during the current trip.

Run Dist of Previous Trip 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Run Dist of Previous Trip
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
-
Yes
Diagnostic Note:
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

HINT:
Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.


Engine Starting Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Starting Time
Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm)/
Min.: 0 ms, Max.: 655350 ms
-
Yes
Diagnostic Note:
This is the time elapsed after the starter turns on until the engine speed reaches 400 rpm.
This value is cleared 5 seconds after the engine is started and the value is displayed as 0 ms.

Previous Trip Coolant Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Coolant Temp
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes
Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip.
After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip.

Previous Trip Intake Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Intake Temp
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes
Diagnostic Note:
Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip.
After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip.

Engine Oil Temperature 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Oil Temperature
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
-
Yes

Previous Trip Eng Oil Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes

Ambient Temp for A/C 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Ambient Temp for A/C
Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
-
Yes

Previous Trip Ambient Temp 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Previous Trip Ambient Temp
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
Yes

Engine Start Hesitation 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Start Hesitation
History of hesitation during engine start/
ON or OFF
-
Yes
Diagnostic Note:
This value changes to ON when the engine speed does not reach 500 rpm during cranking.

Low Rev for Eng Start 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Low Rev for Eng Start
History of low engine speed after engine start/
ON or OFF
-
Yes
Diagnostic Note:
This flag changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine.

Minimum Engine Speed 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Minimum Engine Speed
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
-
Yes
Diagnostic Note:
  1. This is the lowest engine speed detected throughout the trip after the engine is started and ISC learning is completed.
  2. For use when engine stall, starting problems or rough idle is present.

Fuel Cut Elps Time 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Fuel Cut Elps Time
Elapsed time since fuel cut due to high engine speed
Min.: 0 sec Max.: 68746 sec
-
Yes
Diagnostic Note:
  1. The time elapsed after a fuel cut after high engine speed has occurred (More than the rpm at which fuel cut occurs + 500 rpm).
  2. This item is displayed only for Manual Transaxle.

Electric Fan Motor 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electric Fan Motor
Electric fan motors operation status/
ON or OFF
ON: Electric fan motor operating
Yes

Idle Fuel Cut 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Idle Fuel Cut
Fuel cut at idle/
ON or OFF
ON: Fuel cut operating
Yes
Diagnostic Note:
Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high.

FC TAU 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
FC TAU
Fuel cut TAU (fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating
Yes
Diagnostic Note:
This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete.

Immobiliser Fuel Cut 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Fuel Cut
Status of immobiliser fuel cut/
ON or OFF
-
Yes

Immobiliser Fuel Cut History 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history/
ON or OFF
-
Yes

Electrical Load Signal 1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electrical Load Signal 1
Electrical load signal/
ON or OFF
ON: Tail switch ON
Yes

Electrical Load Signal 2 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Electrical Load Signal 2
Electrical load signal/
ON or OFF
ON: Rear defogger switch ON
Yes

Various Vehicle Conditions 5 (Vehicle Information)

Model Code 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Model Code
Model code
-
No
Diagnostic Note:
Used for identifying the model code: NCP13#

Engine Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Type
Engine type
-
No
Diagnostic Note:
Used for identifying the engine type: 1NZFE

Cylinder Number 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Cylinder Number
Number of cylinders/
Min.: 0 Max.: 255
-
No
Diagnostic Note:
Used for identifying the number of cylinders: 4

Transmission Type 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Transmission Type
Transmission type
-
No
Diagnostic Note:
Used for identifying the transmission type: MT / ECT 4th

Destination 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Destination
Destination
-
No
Diagnostic Note:
Used for identifying the destination: W

Model Year 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Model Year
Model year/
Min.: 1900 Max.: 2155
-
No
Diagnostic Note:
Used for identifying the model year: 20##

System Identification 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
System Identification
System identification
-
No
Diagnostic Note:
Used for identifying the engine system: Gasoline (gasoline engine)

Compression (Compression)

Engine Speed of Cyl #1 to #4 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine speed for cylinder No. 1 to No. 4/
Min.: 0 rpm, Max.: 51199 rpm
-
No
Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test.
This is the engine speed for each cylinder measured during the fuel-cut with the engine cranking.
When there is compression loss, the engine speed for that cylinder increases.

HINT:
When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.

Results of real-vehicle check when performing the Active Test with a normal vehicle:
  1. Engine Speed of Cyl #1: 260 rpm
  2. Engine Speed of Cyl #2: 259 rpm
  3. Engine Speed of Cyl #3: 258 rpm
  4. Engine Speed of Cyl #4: 257 rpm

Av Engine Speed of All Cyl 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Av Engine Speed of All Cyl
Average engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
No
Diagnostic Note:
This is output only when Check the Cylinder Compression is performed using the Active Test.

Automatic Transaxle System 1 (All Data)
Refer to Automatic Transaxle System (Click here).

SPD (NT) 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
SPD (NT)
Input shaft speed/
Min.: 0 rpm Max.: 12750 rpm
  1. Lock-up on (after warming up engine): Input turbine speed (NT) equal to engine speed
  2. Lock-up off (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed
Yes
Diagnostic Note:
Data is displayed in increments of 50 rpm.
This item is displayed only for Automatic Transaxle.

Automatic Transaxle System 2 (AT)
Refer to Automatic Transaxle System (Click here).

A/T Oil Temperature 1 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
A/T Oil Temperature 1
ATF temperature sensor value/
Min.: -40°C, Max.: 215°C
  1. After stall test:
    Approximately 80°C (176°F)
  2. Equal to ambient temperature
    when engine cold
Yes
Diagnostic Note:
If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted.
This item is displayed only for Automatic Transaxle.

Lock Up 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Lock Up
Lock up status/
ON or OFF
  1. Lock-up operating: ON
  2. Lock-up not operating: OFF
Yes
Diagnostic Note:
This item is displayed only for Automatic Transaxle.

Shift Status 
Tester Display
Measurement Item/Range
Normal Condition
Stored as Freeze Frame Data
Shift Status
ECM gearshift command/
1st, 2nd, 3rd or 4th
Shift lever in D: 1st, 2nd, 3rd or 4th
Yes
Diagnostic Note:
This item is displayed only for Automatic Transaxle.

ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the tester, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All injectors are tested at the same time.
    2. Perform the test at or below 3000 rpm.
    3. Injection volume can be changed in fine gradations within control range.
    4. Control the Injection Volume enables the checking and graphing of the heated oxygen sensor voltage outputs.
    5. To conduct the test, enter the following menus: Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2.
    6. During the Active Test, air-fuel ratio feedback control and feedback learning are stopped.
    7. See waveform *2
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12.5%/0%/12.5%
    1. All injectors are tested at the same time.
    2. Perform the test at or below 3000 rpm.
    3. Control the Injection Volume for A/F Sensor enables the checking and graphing of the heated oxygen sensor voltage outputs.
    4. To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2.
    5. During the Active Test, air-fuel ratio feedback control and feedback learning are stopped.
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    1. The valve is opened with a 30% duty ratio.
    2. See waveform *4
    Control the Fuel Pump/Speed
    Activate fuel pump
    ON/OFF
    Perform this test with the engine stopped.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 are connected.
    2. OFF: TC and TE1 are disconnected.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the Electric Cooling Fan
    Control electric cooling fan motor
    ON/OFF
    -
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens slowly
    This test is possible when the following conditions are met:
    1. Ignition switch is ON.
    1. Engine is stopped.
    1. Accelerator pedal is fully depressed (APP: 58 degrees or more).
    2. Shift lever is in P.
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens quickly
    1. Same as above.
    2. See waveform *3
    Control the VVT Linear (Bank 1)
    Control VVT
    -128 to 127% (This value added to present camshaft timing oil control valve control duty)
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stalls or idles roughly when the VVT actuator is operated by 100%.
    2. Test is possible during idle.
    3. See waveform *5
    4. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 1)
    Turn camshaft timing oil control valve on and off
    ON/OFF
    ON: VVT OCV Duty #1 100%
    1. Engine stalls or idles roughly when the camshaft timing oil control valve is turned on.
    2. Engine runs and idles normally when the camshaft timing oil control valve is off.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test is possible while the vehicle is stopped and the engine is idling.
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Test is possible while the vehicle is stopped and the engine is idling.
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Test is possible while the vehicle is stopped and the engine is idling.
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Test is possible while the vehicle is stopped and the engine is idling.
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    Test is possible while the vehicle is stopped and the engine is idling.
    Check the Cylinder Compression*1
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders.

    HINT:
    *1: When cranking the engine, each cylinder measures the engine speed.
    In this Active Test, the fuel and ignition of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the tester on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).


    10. A242113
      Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the tester.

      HINT:
      At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
      3. Use a fully-charged battery.

    11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    12. Push the snapshot button to turn the snapshot function off.
    13. Select "Stored Data" on the intelligent tester screen, select the recorded data and display the data as a graph.

      HINT:
      If the data is not displayed as a graph, the change of the values cannot be observed.

    14. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.

  1. Reference Waveforms for Active Test

    1. *2: Control the Injection Volume (Idling after warming up)


      A257866E02

      HINT:
      During the Active Test, air-fuel ratio feedback control and feedback learning are stopped.


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the Injection Volume
      -
      ▲A
      ▲B
      Active Test operation
      +12%
      -12%
      O2S B1S1
      0.875 V
      0.015 V
      O2S B1S2
      0.740 V
      0.015 V

      HINT:
      1. Usually, the value of O2S changes to 0.5 V or higher when the control value for Control the Injection Volume is changed to +12%.
      2. Usually, the value of O2S changes to below 0.4 V when the control value for Control the Injection Volume is changed to -12%.
      3. The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
      4. Change the fuel injection volume function provided in the Active Test and monitor the heated oxygen sensor output voltage. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    2. *3: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Ignition switch ON)


      A257865E02

      HINT:
      1. Usually, Throttle Position Command (Target Value) and Throttle Position No. 1 (Actual Value) are almost the same.
      2. If any DTCs related to the ETCS are stored, this Active Test does not function.


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the ETCS Open/Close Fast Speed
      -
      ▲A
      ▲B
      Active Test operation
      Open
      Close
      Throttle Position Command
      2.597 V
      0.800 V
      Throttle Position No. 1
      2.597 V
      0.800 V
      Throttle Motor Duty (Open)
      18%
      0%
      Throttle Motor Duty (Close)
      0%
      17%

    3. *4: Activate the VSV for Evap Control (Idling after warming up)


      A257862E01

      HINT:
      Even when the Active Test is turned on (the purge VSV is opened 30%), air-fuel ratio feedback continues and control is performed so that the air-fuel ratio is the stoichiometric ratio. Therefore, by observing the change in "Short FT", it is possible to determine whether the purge VSV is actually open as well as the concentration of HC in the purge gas.


      Tester Display
      Measurement Item/Range
      Normal Condition
      Activate the VSV for Evap Control
      -
      ▲A
      ▲B
      Active Test operation
      ON
      OFF
      EVAP (Purge) VSV
      29.8%
      0.0%
      Short FT #1
      -9.375%
      3.125%
      Injection (Port)
      2300 μs
      2641 μs
      AFS Voltage B1S1
      0.075 V
      0.035 V

      HINT:
      The graphs and values above are for reference only because the feedback volume varies depending on the HC density of the purge air (HC volume absorbed by the canister).


    4. *5: Control the VVT Linear (Bank 1)


      A258722E01


      Tester Display
      Measurement Item/Range
      Normal Condition
      Control the VVT Linear (Bank 1)
      -
      ▲A
      ▲B
      Active Test operation*
      +30%
      -30%
      VVT Change Angle #1
      31.0 DegFR
      0.0 DegFR
      VVT OCV Duty #1
      67.0 %
      7.0 %
      VVT Aim Angle #1
      37.0 %
      37.0 %

      HINT:
      1. *: Change the control value for Control the VVT Linear to +30% or -30% in increments of 5%.
      2. The Control the VVT Linear Active Test considers the value of VVT Aim Angle to be 0 and raises or lowers the duty ratio with respect to VVT Aim Angle.
      3. The sum of the control value for the Control the VVT Linear Active Test and the value of VVT Aim Angle is approximately equal to the value of VVT OCV Duty.
      4. When the control value for the Control the VVT Linear Active Test is changed a few times, there should not be a large discrepancy between VVT OCV Duty when the system starts advancing or retarding the timing and the rate of change of VVT Change Angle.