Home › Engine / Hybrid System ยท 2NZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

for Preparation Click here


MONITOR DESCRIPTION

The ECM uses the heated oxygen sensors mounted in front of and behind the Three-way Catalytic Converter (TWC) to monitor its efficiency. The front heated oxygen sensor (sensor 1) sends pre-TWC air-fuel ratio information to the ECM, and the rear heated oxygen sensor (sensor 2) sends post-TWC air-fuel ratio information to the ECM. The ECM compares the 2 signals to assess the efficiency of the TWC and the TWC's ability to store oxygen. During normal operation, the TWC stores and releases oxygen as needed. This capacity to store oxygen reduces the variation in the post-TWC exhaust stream as shown below.
If the TWC is functioning normally, the waveform of sensor 2 slowly fluctuates between rich and lean.
As the TWC efficiency deteriorates, its ability to store oxygen reduces and the sensor output becomes more variable.
When the TWC monitor runs, the ECM measures the signal lengths of both sensors 1 and 2, and then calculates the ratio of the signal lengths (TWC deterioration level). If the TWC deterioration level exceeds the threshold, the ECM interprets this as a TWC malfunction. The ECM illuminates the MIL and stores the DTC.

A133486E01


A133487E01


DTC No.
DTC Detection Condition
Trouble Area
P0420
The ratio of the signal lengths (the signal length of oxygen sensor 2 divided by the signal length of oxygen sensor 1) smaller than standard value
(2 trip detection logic)
  1. Heated oxygen sensor (sensor 1)
  2. Heated oxygen sensor (sensor 2)
  3. Gas leakage from exhaust system
  4. Front exhaust pipe assembly (with TWC)

CATALYST LOCATION


A256952E03


*1
Exhaust Manifold
*2
Heated Oxygen Sensor (Sensor 1)
*3
Front Exhaust Pipe Assembly (TWC: Front and Rear Catalyst)
*4
Heated Oxygen Sensor (Sensor 2)
*5
Tail Exhaust Pipe Assembly
-
-

MONITOR STRATEGY


Required Sensors/Components (Main)
Catalyst
Required Sensors/Components (Related)
Heated oxygen sensor, Intake air temperature sensor, Mass air flow meter, Crankshaft position sensor, Engine coolant temperature sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Accumulated time that all of following conditions are met
30 seconds
Battery voltage
11 V or more
Intake air temperature
-10°C (14°F) or more
Idle status
OFF
Engine speed
Less than 4000 rpm
Engine coolant temperature
75°C (167°F) or more
Fuel system status
Closed loop
Front catalyst temperature
530°C (986°F) or more
Rear catalyst temperature
530°C (986°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Heated oxygen sensor (sensor 2) locus length
0.45 V or more (varies with heated oxygen sensor locus length)
Frequency of the monitor
3 times

CONFIRMATION DRIVING PATTERN

HINT:
Perform this confirmation driving pattern will activate the catalyst monitor. this is very useful for verifying the completion of a repair.


A231470E80

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  8. Enter the following menus: Powertrain / Engine and ECT / DTC [C].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P0420.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [D] through [E].

  13. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  14. Check the DTC judgment result again [E].

CONDITIONING FOR SENSOR TESTING


A118003E96

(a) Connect the intelligent tester to the DLC3 [A].
(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature becomes stable [B].
(c) Run the engine at 2500 to 3000 rpm for about 3 minutes [C].
(d) While running the engine at 3000 rpm for 2 seconds and 2000 rpm for 2 seconds, check the waveforms of the heated oxygen sensors using the tester [D].

HINT:
Control the engine speed so that the calculated catalyst temperature can be 530°C (986°F) or more. The calculated catalyst temperatures can be read by viewing Catalyst Temp (B1S1) and Catalyst Temp (B1S2) of the Data List.

A093282E30

HINT:
If there is a malfunction in the TWC, the waveform of the heated oxygen sensor (sensor 2) is almost the same as that of the heated oxygen sensor (sensor 1).


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0420 is output
    A
    DTC P0420 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Turn the tester on.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the heated oxygen sensor (O2S B1S1 and O2S B1S2) displayed on the tester.

    HINT:
    1. Change the fuel injection volume within the range of - 12% to +12%. The injection volume can be changed in fine gradations.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    O2S B1S1
    (Heated oxygen sensor (sensor 1))
    +12%
    Rich
    Higher than 0.5 V
    -12%
    Lean
    Below 0.4 V
    O2S B1S2
    (Heated oxygen sensor (sensor 2))
    +12%
    Rich
    Higher than 0.5 V
    -12%
    Lean
    Below 0.4 V


    Result 
    Status
    O2S B1S1
    Status
    O2S B1S2
    Actual Air-Fuel Ratio,
    Heated Oxygen Sensor Condition
    Misfire
    Main Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-way catalytic converter
    2. Gas leak from exhaust system
    A
    Lean
    Lean/Rich
    Heated oxygen sensor (sensor 1) malfunction
    -
    1. Heated oxygen sensor (sensor 1)
    B
    Rich
    Lean/Rich
    Heated oxygen sensor (sensor 1) malfunction
    -
    1. Heated oxygen sensor (sensor 1)
    Lean/Rich
    Lean
    Heated oxygen sensor (sensor 2) malfunction
    -
    1. Heated oxygen sensor (sensor 2)
    2. Gas leak from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor (sensor 2) malfunction
    -
    1. Heated oxygen sensor (sensor 2)
    2. Gas leak from exhaust system
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leak from exhaust system
    D
    Rich
    Rich
    Actual air-fuel ratio rich
    -
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leak from exhaust system
    Lean: During Control the Injection Volume, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.
    Rich: During Control the Injection Volume, and the O2S B1S2 is consistently higher than 0.5 V.
    Lean/Rich: During Control the Injection Volume of the Active Test, the output voltage of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) alternate correctly.



B
Go to step 5

C
Go to step 6

D
Go to step 8
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


4.REPLACE EXHAUST PIPE ASSEMBLY FRONT (TWC: FRONT AND REAR CATALYST)

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the exhaust pipe assembly front (TWC: Front and rear catalyst) (Click here).


NEXT

END 

5.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)
  1. Replace the heated oxygen sensor (sensor 1) (Click here).



NEXT
Go to step 11

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


7.REPLACE HEATED OXYGEN SENSOR (SENSOR 2)
  1. Replace the heated oxygen sensor (sensor 2) (Click here).



NEXT
Go to step 11

8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 10
OK


9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO
  1. Check the cause of extremely rich or lean actual air-fuel ratio, referring to the DTC P0171 Inspection Procedure .



NEXT
Go to step 11

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace the exhaust gas leak point.


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result
    Proceed to
    DTC P0420 is output
    A
    DTC is not output
    (No pending DTCs output)
    B



B
END
A


12.REPLACE EXHAUST PIPE ASSEMBLY FRONT (TWC: FRONT AND REAR CATALYST)

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Replace the exhaust pipe assembly front (TWC: Front and rear catalyst) (Click here).


NEXT

END