Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus:
    Body / Main Body / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / OFF or ON
    OFF: No key is in ignition key cylinder
    ON: Key is in ignition key cylinder
    -
    ACC SW
    Ignition switch status / OFF or ON
    OFF: Ignition switch off
    ON: Ignition switch on (ACC)
    -
    IG SW
    Ignition switch status / OFF or ON
    OFF: Ignition switch off
    ON: Ignition switch to ON
    -
    RR Door Courtesy SW*1
    Rear door courtesy light switch LH and RH signal / OFF or ON
    OFF: Rear door LH and RH closed
    ON: Rear door LH or RH opened
    -
    RL Door Courtesy SW*1
    Rear door courtesy light switch LH and RH signal / OFF or ON
    OFF: Rear door LH and RH closed
    ON: Rear door LH or RH opened
    -
    Back Door Courtesy SW
    Back door courtesy switch signal / OFF or ON
    OFF: Back door closed
    ON: Back door opened
    -
    Back Door Open
    Back door open status / Prohibit or Permit
    Prohibit: Back door locked
    Permit: Back door unlocked
    -
    Door Lock SW-Lock
    Door manual lock switch signal / OFF or ON
    OFF: Door control switch (for front driver door side) is turned to unlock position
    ON: Door control switch (for front driver door side) is turned to lock position
    -
    Door Lock SW-Unlock
    Door manual unlock switch signal / OFF or ON
    OFF: Door control switch (for front driver door side) is turned to lock position
    ON: Door control switch (for front driver door side) is turned to unlock position
    -
    Door Key SW-Lock
    Door key lock and unlock switch signal/ OFF or ON
    OFF: Driver side door key cylinder not turned
    ON: Driver side door key cylinder turned to lock position
    -
    Door Key SW-Unlock
    Door key lock and unlock switch signal/ OFF or ON
    OFF: Driver side door key cylinder not turned
    ON: Driver side door key cylinder turned to unlock position
    -
    FR Door Lock Pos*3
    Front door unlock detection switch RH signal / LOCK or UNLOCK
    LOCK: Front RH locked
    UNLOCK: Front RH door unlocked
    -
    FR Door Courtesy
    Front RH door courtesy light switch signal / ON or OFF
    ON: Front RH door closed
    OFF: Front RH door opened
    -
    FL Door Lock Pos*2
    Front door unlock detection switch LH signal / LOCK or UNLOCK
    LOCK: Front LH side door locked
    UNLOCK: Front LH side door unlocked
    -
    FL Door Courtesy
    Front LH door courtesy light switch signal / ON or OFF
    ON: Front LH door closed
    OFF: Front LH door opened
    -
    Back Door Open Handle SW
    Back door opener switch signal / OFF or ON
    OFF: Back door opener switch not pushed
    ON: Back door opener switch pushed
    -
    RR-Door Lock Pos SW*1
    Not available / OFF or ON
    -
    -
    RL-Door Lock Pos SW*1
    Not available / OFF or ON
    -
    -

    1. *1: for 5 Door
    2. *2: for LHD
    3. *3: for RHD


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus:
    Body / Main Body / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Door Lock
    Door lock motor
    OFF / Unlock / Lock
    -
    Trunk and Back-Door Open
    Back door lock motor
    OFF / ON
    -