Home › Drivetrain ยท DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE ENGINE UNDER COVER LH (for Plastic Type)


2. REMOVE ENGINE UNDER COVER RH (for Plastic Type)


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)


4. DRAIN TRANSAXLE OIL (for Manual Transaxle)
  1. Remove the manual transmission filler plug and the gasket.

  1. Remove the drain plug sub-assembly and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug sub-assembly.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



5. DRAIN AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



6. REMOVE FRONT WHEEL


7. REMOVE FRONT AXLE SHAFT NUT LH


C236996E01
  1. Using SST and a hammer, release the staked part of the front axle shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the front axle shaft nut.
    4. Do not damage the threads of the front drive shaft.

  1. Using a deep socket wrench 30 mm, remove the front axle shaft nut.



8. REMOVE FRONT AXLE SHAFT NUT RH

HINT:
Use the same procedure for the RH side as for the LH side.



9. SEPARATE FRONT SPEED SENSOR LH (w/ ABS)


    C107502
  1. Remove the bolt and separate the speed sensor and flexible hose.



    C112274
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.



10. SEPARATE FRONT SPEED SENSOR RH (w/ ABS)

HINT:
Use the same procedure for the RH side as for the LH side.



11. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C235696
  1. Remove the nut and separate the stabilizer link assembly LH from the front stabilizer bar.

    HINT:
    Using a socket hexagon wrench 6 to hold the stud.



12. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



13. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C172757E03
  1. Install SST to the threaded section of the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the front axle assembly.


    C172758E03


    Text in Illustration 
    *a
    Place the wrench here
    -
    -
    V100135
    Apply grease to the bolt threads and the tip of SST.
    -
    -
    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the ball joint dust cover.
    5. Do not damage the front disc brake dust cover.



14. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



15. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH
  1. Remove the clip and castle nut.



    C172759E05
  1. Install SST to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST are aligned.



  1. Using SST, separate the lower arm.


    C172760E06


    Text in Illustration 
    *a
    Place the wrench here
    -
    -
    V100135
    Apply grease to the bolt threads and the tip of SST.
    -
    -
    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    2. Install SST so that A and B are parallel.
    3. Be sure to place the wrench on the part indicated in the illustration.
    4. Do not damage the lower ball joint dust cover.
    5. Do not damage the drive shaft outboard joint boots.
    6. Do not damage the front disc brake dust cover.



16. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



17. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.



18. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



19. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C107924E02
  1. Using SST, remove the drive shaft as shown in the illustration.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



20. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C241892
  1. Using a tire lever and brass bar, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



21. FIX FRONT AXLE ASSEMBLY


C112583E01
SST
09608-16042   (09608-02021, 09608-02041)

HINT:
The hub bearing could be damaged if it is subjected to the vehicle's full weight, such as when moving the vehicle with the drive shaft removed. If it is absolutely necessary to place the vehicle's full weight on the hub bearing, first support it with SST.